Fujitsu AIRSTAGE AJH072LALBH, Installation Manual

Page: 20 / 26

En-19
72
Electricity meter
pulse setting 1 *3
Setting number (xx00)
7 2
0 0 
Setting number (xx01) 0 1
······ ··· ···
Setting number (xx98) 9 8
Setting number (xx99) 9 9
Set the ones digit and tens digit of the No. of the electricity meter pulse setting
connected to CN135.
73
Electricity meter
pulse setting 2 *3
Setting number (00xx)
7 3
0 0

Setting number (01xx) 0 1
······ ··· ···
Setting number (98xx) 9 8
Setting number (99xx) 9 9
Set the hundreds digit and thousands digit of the electricity meter pulse setting
connected to CN135.
*1: Do not set this for outdoor units with Slave setting.
*2: When electricity meter No. is set to “000” and “201 to 299”, the pulses input to CN135
become ineffective. Available setting number is "001" to "200"
*3: When the electricity meter pulse setting is set to “0000”, the pulses input to CN135
become ineffective. Available setting number is "0001" to "9999"
(1) Turn on the power of the outdoor unit and enter standby mode.
• When system is normal
POWER/MODE lamp lights up. (ERROR lamp is off.)
POWER/MODE lamp:
ON
ERROR lamp: OFF
SELECT button
ENTER button
MODE/EXIT button
POWER
LED105 LED104
ERROR
MODE
LED101
(GREEN)
MODE
/EXIT
SELECT ENTER
SW107 SW108 SW109
LED102
(RED)
7 segment LED indicator:
OFF
• When system is abnormal
Check the settings as there is an error in the settings for outdoor unit address (DIP switch
SET3-1, 2) or number of connected slave units (DIP switch SET3-3, 4).
POWER/MODE lamp:
ON
7 segment LED indicator:
"-" display
ERROR lamp:
Blinking
POWER
LED105 LED104
ERROR
MODE
LED101
(GREEN)
MODE
/EXIT
SELECT ENTER
SW107 SW108 SW109
LED102
(RED)
(2) Setting method
Use the “MODE/EXIT”, “SELECT”, and “ENTER” buttons to con
fi gure settings accord-
ing to the procedures below.
(If no setting is made, the factory default setting will be displayed.)
: Press the “MODE/EXIT” button.
: Press the “SELECT” button.
: Press the “ENTER” button.
: Press the “ENTER” button for more than 3 seconds.
MODE/EXIT
SELECT
ENTER
ENTER
1: FUNCTION Setting
7 segment LED indicator
(LED105, LED104)
(Flashing)
First 2 digits Last 2 digits
(When [F3] to [F9] are displayed, continue to press
the “SELECT” button until [F2] is displayed.)
2: Setting the
fi rst 2 digits
3: Setting the last 2 digits
Continue to press the “SELECT” button
until the desired number appears at the
last 2 digits.
Every press of the
“SELECT” button will
change the setting
number for the fi rst 2
digits.
(Continue to press the
“SELECT” button until the
desired number appears at
the last 2 digits.)
Setting is complete when the lamp lights up
Press “ENTER” button to return to “2. Setting
the first 2 digits” (If there is no operation for
5 seconds after the setting, the indicator will
return to “2: Setting the first 2 digits”.)
Setting is complete when the lamp lights up
Press “ENTER” button to return to “2. Setting the
fi rst 2 digits” (If there is no operation for 5 seconds
after the setting, the indicator will return to
“2: Setting the fi rst 2 digits”.)
EXIT: Press the “MODE/EXIT” button to cancel the setting mode.
MODE/EXIT
SELECT
ENTER
ENTER
MODE/EXIT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
ENTER
MODE/EXIT
MODE/EXIT
ENTER
ENTER
9378945180-02_IM.indb 19 9378945180-02_IM.indb 19 2014/11/10 19:39:58 2014/11/10 19:39:58