Fujitsu ABHG18KRTA Service Manual Download Page 294

Page: 294 / 471

4-6. Mobile app setting method

Air conditioner deregistration method

When the wireless LAN adapter is replaced, deregistration of all air conditioner is necessary on the
mobile app.

Launch the mobile app.

FGL air

Press and hold the registered device name of the air conditioner.

If the Unregister button is displayed, tap the button.

Tap the Yes button.

Deregstration of the air conditioner is completed.

4-6. Mobile app setting method

- (03-78) -

4. Troubleshooting with error code (For wireless LAN adapter)

TROUBLESHOOTING

Summary of Contents for ABHG18KRTA
























































































































































































































































































































































































































































































Search results

Summary of Contents for ABHG18KRTA

Reviews:

Related manuals for ABHG18KRTA

Brands by name

Popular brands

Fujitsu ABHG18KRTA, Service Manual

Search results

Summary of Contents for ABHG18KRTA

Reviews:

Related manuals for ABHG18KRTA

Brands by name

Popular brands