Fujitsu ABHG18KRTA Service Manual Download Page 267

Page: 267 / 471

2-35. E: 94. Over current error (Outdoor unit)

Indicator

Indoor unit

Operation indicator

9 time flash

Timer indicator

4 time flash

Economy indicator

Continuous flash

Error code

E: 94

Detective actuator

Outdoor unit

Main PCB

1. When more than normal operating current to IPM in

main PCB flows, the compressor stops.

2. After the compressor restarts, if the same operation

is repeated within 40 seconds, the compressor
stops again.

3. If 1. and 2. repeats 5 times, the compressor stops

permanently.

Compressor

Forecast of cause

Defective connection of electrical components

Outdoor fan operation failure

Outdoor heat exchanger clogged

Compressor failure

Main PCB failure

Check point 1. Check connections of outdoor unit electrical components

•

Check if the terminal connection is loose.

•

Check if connector is removed.

•

Check erroneous connection.

•

Check if cable is open.

→ Upon correcting the removed connector or mis-wiring, reset the power.

↓

Check point 2. Check outdoor fan and heat exchanger

•

Is there anything obstructing the air distribution circuit?

•

Is there any clogging of outdoor heat exchanger?

•

Is the fan rotating by hand when operation is off?

→ If the fan motor is locked, replace it.

↓

Check point 3. Check outdoor fan

Check outdoor fan motor.
Refer to

"E: 97. Outdoor unit fan motor error (Outdoor unit)"

on page 03-54.

→ If the fan motor is failure, replace it.

↓

2-35. E: 94. Over current error (Outdoor unit)

- (03-51) -

2. Troubleshooting with error code

TROUBLESHOOTING

Summary of Contents for ABHG18KRTA
























































































































































































































































































































































































































































































Search results

Summary of Contents for ABHG18KRTA

Reviews:

Related manuals for ABHG18KRTA

Brands by name

Popular brands

Fujitsu ABHG18KRTA, Service Manual

Search results

Summary of Contents for ABHG18KRTA

Reviews:

Related manuals for ABHG18KRTA

Brands by name

Popular brands