background image

En-12

SWING OPERATION

Begin air conditioner operation before performing this procedure.

Up/down swing operation

Left/right swing operation

Swing operation stops

Up/down/left/right swing operation

To select SWING Operation

Press the SWING button.

The SWING Display will light.
Each time the SWING button is pressed, the swing operation will change in the follow-
ing order.

To stop SWING Operation

Press the SWING button and select STOP.

Air

fl

 ow direction will return to the setting before swing was begun.

About SWING Operation

The type of operation

Cooling/Dry

Heating

FAN

Range of swing

1

 to 

5

 (All range)

1

 to 

5

 (All range)

1

 to 

5

 (All range)

The SWING operation may stop temporarily when the air condi-
tioner’s fan is not operating, or when operating at very low speeds.

  To select left/right swing operation

*1 

The position of the louvers before swing is given in paren-
thesis. 

The type of operation

Cooling/Dry

Heating

FAN (

1

 ~ 

4

)

*1

FAN (

5

 ~ 

7

)

*1

Range of swing

1

 to 

4

3

 to 

7

1

 to 

4

3

 to 

7

The SWING operation may stop temporarily when the air condi-
tioner’s fan is not operating, or when operating at very low speeds.

  To select up/down swing operation

ECONOMY OPERATION

Begin air conditioner operation before performing this procedure.

To Use the ECONOMY Operation

Press the ECONOMY button.

The ECONOMY indicator lamp (green) will light.
ECONOMY operation begins.

To Stop the ECONOMY Operation

Press the ECONOMY button again.

The ECONOMY indicator lamp (green) will go out.
Normal operation begins.

About ECONOMY Operation

At the maximum output, ECONOMY operation is approximately 70% of normal air conditioner operation for cooling and heating.

  If the room is not cooled (or heated) well during ECONOMY operation, select normal operation.

  During the monitor period in the AUTO mode, the air conditioner operation will not change to ECONOMY operation even if ECON-

OMY operation is selected by pressing the ECONOMY operation button.

  When ECONOMY operation mode is operated, the room temperature will be little higher than the set-temp under cooling mode 

and lower than set-temp under heating mode. Therefore, the ECONOMY mode is able to save more energy than other normal 
mode.

  In case of multi-type air conditioner, the ECONOMY operation mode is only available for the set indoor unit.

  Indicator Lamp

: Lighting

: OFF

9374379729_OM.indb   12

9374379729_OM.indb   12

24/06/2013   09:41:18

24/06/2013   09:41:18

Summary of Contents for ABF14UI-MI



















Reviews: