manualshive.com logo in svg

Fujitsu Siemens Computers Primergy RX220, Service Supplement Manual

Share
Download
Fujitsu Siemens Computers Primergy RX220 Service Supplement Manual Download Page 38

38

Service Supplement

 RX220

Replacing the system board

Replacement routines

4.10

Replacing the system board

Ê

Open the server as described in the 

section “Preparation” on page 17

.

Ê

Disconnect all external cables on the rear side of the server 

Removing the system board

Ê

Remove the memory modules (the relevant procedure is described in the 
Options Guide).

Ê

Remove the air duct, the heat sink(s) and processor(s) 
(the relevant procedure is described in the Options Guide).

Ê

Remove the riser card holders (the relevant procedure is described in the 
Options Guide).

Ê

Remove all cables connected to the system board.

Figure 25: Positions of the screws on the system board

Ê

Remove 11 system board screws (see figure on 

page 38

).

Ê

Push the system board about 1 am in the direction of the housing front. 

Summary of Contents for Primergy RX220






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands