background image

· Always wear appropriate gloves and eye protection
· Always wear a respirator or mask. Read all instructions of the

respirator or mask to ensure that it will provide the necessary
 protection against the inhalation of harmful vapors. Please also check
with the local jurisdiction.

·  Paint, solvents, insecticides and other materials may be harmful if

inhaled.

·  Store hazardous fl uid in approved containers, and dispose of it

according to applicable guideline.

·  Do not stop or defl ect fl uid leaks with your hand or body.

  EQUIPMENT MISUSE HAZARD

Misuse of equipment can cause serious injury or death.      

· Never aim the spray gun at another person or animal. In the event of

injury, seek expert medical advice immediately.

· Do not operate or spray near children. Keep children away from

equipment at all times.

· Do not overreach or stand on an unstable support. Keep eff ective

footing and balance at all times.

· Stay alert and watch what you are doing.
· Do not operate the unit when fatigued or under the infl uence of drugs

or alcohol.

· Do not kink or over-bend the hose.
· Do not use the hose as a strength member to pull or lift the

equipment.

· Do not cover turbine case as this will restrict air to the intake and

result to overheating and premature failure of the motor.

· Do not carry turbine while spraying.
· Check the hose, hose connectors and power cord daily. Any worn or

damaged parts should be replaced immediately.

· Use only genuine Fuji Spray replacement parts.
· It is normal for the turbine air outlet (manifold) to become hot during

use, please allow your Fuji Spray turbine to cool for a few minutes
before removing the hose from the turbine manifold.

4

Prop 65 Warning for California Residents        
WARNING: 

This product may contain chemicals known 

to the State of California to cause cancer, birth defects, or 
other reproductive harm.

21

#2095

Summary of Contents for M-MODEL

























Reviews: