Fuji Xerox DocuPrint P355 d User Manual Download Page 73

Page: 73 / 272

Printer Connection and Software Installation

Specify the value of the gateway address using the

button.

Press the

button.

The cursor moves to the next octet.

Repeat steps

to set the gateway address, and then press the

button.

Ensure that the message

Restart Printer to apply setting

appears, and then press the

(

Back

)

button.

Turn off and turn on the printer.

IMPORTANT:

•

Note that the data in the memory are cleared when the printer is turned off.

See also:

• "Operator Panel" on page 34



Verifying the IP Settings

You can confirm the settings by printing the system settings report or using the ping command.
The following procedure uses Windows 7 as an example.

Print the Printer Settings page.

Look under the

IPv4

heading on the Printer Settings page to ensure that the IP address, subnet mask, and

gateway address are appropriate.

To verify if the printer is active on the network, run the ping command in your computer:

Click

Start

→

All Programs

→

Accessories

→

Run

Enter

cmd

, and then click

A black window is displayed.

Enter

ping xx.xx.xx.xx

(where

xx.xx.xx.xx

is the IP address of your printer), and then press the

Enter

key.

Reply from the IP address denotes printer is active on the network.



Printing and Checking the Printer Settings Page

Print the Printer Settings page and check your printer's IP address by using the operator panel.

On the operator panel, press the

(

Menu

) button.

Select

Report / List

, and then press the

button.

Select

Printer Settings

, and then press the

button.

The Printer Settings page is printed.

Confirm the IP address next to

IP Address

under

Wired Network

on the Printer Settings page. If the IP

address is

0.0.0.0

, wait for a few minutes to resolve the IP address automatically, and then print the Printer

Settings page again.
If the IP address is not resolved automatically, see

"Assigning an IP Address (for IPv4 Mode)" on page 72

Summary of Contents for DocuPrint P355 d
















































































































































































































































































Search results

Summary of Contents for DocuPrint P355 d

Reviews:

Related manuals for DocuPrint P355 d

Brands by name

Popular brands

Fuji Xerox DocuPrint P355 d, User Manual

Search results

Summary of Contents for DocuPrint P355 d

Reviews:

Related manuals for DocuPrint P355 d

Brands by name

Popular brands