Fuji Xerox DocuPrint CM225FW Page 206 User Manual Download

Page: 206 / 344

206

Using the Operator Panel Menus and Keypad

Understanding the Printer Menus

This section describes menu options that can be accessed by pressing the

(

System

) button on the operator

panel.

NOTE:

•

The access to

Admin Settings

and

Report

List

can be limited with a password by enabling the Panel Lock function.

For more information, see "Panel Lock Function" on page 250.



Report / List

Use

Report

List

to print various types of reports and lists.

NOTE:

•

A password is required to enter the

Report

List

menu when

Panel Lock Set

is set to

Enable

. In this case, enter the

password you specified, and then select

System Settings

Purpose:
To print a list of the information such as the printer name, serial number, and print volume.
Network settings are also printed.

Panel Settings

Purpose:
To print a detailed list of all the settings on the operator panel menus.

PCL Fonts List

Purpose:
To print a sample of the available PCL fonts.

PS Fonts List

Purpose:
To print a sample of the available PS fonts.

Job History

Purpose:
To print a detailed list of the jobs that have been processed. This list contains the last 50 jobs.

Error History

Purpose:
To print a detailed list of paper jams and fatal errors.

Demo Page

Purpose:
To print a test page.

Protocol Monitor

Purpose:
To print a detailed list of monitored protocols.

Summary of Contents for DocuPrint CM225FW
























































































































































































































































































































































Search results

Summary of Contents for DocuPrint CM225FW

Reviews:

Related manuals for DocuPrint CM225FW

Brands by name

Popular brands

Fuji Xerox DocuPrint CM225FW, User Manual

Search results

Summary of Contents for DocuPrint CM225FW

Reviews:

Related manuals for DocuPrint CM225FW

Brands by name

Popular brands