Fuji Xerox DocuPrint C1110 B User Manual Download | Manualshive

Page: 140 / 209

background image

140

7 Maintenance

Checking the Meter Reading by Computer (Meter Report)

The [Meter Report] shows the number of printed page/sheets for each computer (job
owner).
The [Meter Report] can be printed from the control panel.

Note

• When the Authentication and Auditron Administration features are enabled, you can print the [Auditron

Report] instead of the [Meter Report].

• If you enable the Authentication and Auditron Administration features, the meter counts will reset to “0”.
• You can reset the meter counts under [Maintenance Mode] > [Printer Meter] on the control panel.

Refer to

• For information on how to print the [Meter Report], refer to "Printing the Reports/Lists" (P. 137).

Meter Report

The [Meter Report] lists the following items.

Job Owner Name

Up to 50 owner names can be printed. The print count of the 51th job owner
or a user without a job owner name will be listed under "UnknownUser"
(second from the last row). The printing of this report is also counted in
"Report/List" (the last row in the report).

Pages - Color 8.5 x 14

Total number of pages printed in color on 8.5 x 14" size paper.

Pages - Color A4

Total number of pages printed in color on A4 size paper.

Pages - Color 8.5 x 11

Total number of pages printed in color in 8.5 x 11" size paper.

Pages - Color B5

Total number of pages printed in color on B5 size paper.

Pages - Color Others

Total number of pages printed in color on paper other than the above.

Pages - Color Total

Total number of pages printed in color.

Pages - Black Total

Total number of pages printed in monochrome.

Pages - Total Pages

Total number of pages printed. Printed pages are counted after every print
job.

Sheets - Color Sheets

Total number of sheets

*1

printed in color.

Sheets - Black Sheets

Total number of sheets

*1

printed in monochrome.

Sheets - Total Sheets

Total number of sheets

*1

printed. Printed sheets are counted after every

print job.

*1

: If you perform 2-sided printing on this printer, "1 page" is counted as "1 sheet".

For example, if printing 4 pages with 2-sided printing, the printed sheets are counted as "4 sheets".

«
...
138
139
140
141
142
...
»

Summary of Contents for DocuPrint C1110 B


















































































































































































































Reviews:

No comments

Related manuals for DocuPrint C1110 B

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 2

Brand: Samsung Pages: 322

Brand: Samsung Pages: 340

Brand: Samsung Pages: 349

Brand: Samsung Pages: 330

Brand: Samsung Pages: 315

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 232

Brand: Samsung Pages: 42

SCX-6545N Series

Brand: Samsung Pages: 468

Brand: Samsung Pages: 196

SCX4521F - B/W Laser - All-in-One

Brand: Samsung Pages: 120

Brand: Lanier Pages: 3

Brand: Oki Pages: 268

Brand: Oki Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands