Fuji Xerox DocuCentreS2320 User Manual Download | Manualshive

Page: 182 / 257

background image

11 Maintenance

182

M

a

int
e

na
nc
e

11

Replacing the Drum Cartridge

The messages below appear in the control panel display when the drum cartridge is near the
end of its service life. Follow the instructions in the message to take the required action.

* : The service life values shown are the total number of A4 (

) pages that can be printed. Actual remaining service life will vary

depending on the paper size and orientation, number of consecutive pages printed, and the machine's operating environment.
Use the figures above only as a guideline.

Important •

The use of drum cartridges not recommended by Fuji Xerox may lower the machine's output quality
or performance. Always use drum cartridges recommended by Fuji Xerox in the machine.

Note

•

Do not expose drum cartridges to direct sunlight or strong indoor fluorescent lights. Do not touch or
scratch the drum surface. Print quality may be affected.

1

Make sure that the machine is not operating, and
open the front cover.

Error Code

Message

Required Action

091-440

Drum Near End of Life
Drum cartridge is near end of life.
Reorder a drum cartridge.

The drum cartridge will need to be replaced
after about 4,000 pages*. Have a
replacement drum cartridge ready.

091-402
091-441

Drum Near End of Life
Drum cartridge is near end of life.
Replace drum cartridge soon.

The drum cartridge will need to be replaced
after about 1,000 pages*. Have a
replacement drum cartridge ready.

091-430

Drum End of Life
Replace drum cartridge.

The error icon is lit. The drum cartridge
needs to be replaced. Replace the drum
cartridge.

091-401

Drum Near End of Life
Image quality problem may occur.
Replacement of drum cartridge is
recommended.

The error icon is lit. It is time of expiration
for the warranty period of the image quality
on the drum cartridge.

091-406

Drum end of Life
Machine problem may occur.
Replace drum cartridge.

The error icon is lit. It is time of expiration
for the warranty period of performance on
the drum cartridge.

091-424

Drum End of Life
Machine problem will occur soon.
Replace drum cartridge
immediately.

The error icon is lit. The machine detected a
failure due to the use of a dram cartridge
that is not supported.
Replace the drum cartridge immediately.

«
...
180
181
182
183
184
...
»

Summary of Contents for DocuCentreS2320


































































































































































































































































Reviews:

No comments

Related manuals for DocuCentreS2320

imageRUNNER ADVANCE DX 6870i

Brand: Canon Pages: 115

imagerunner advance C5550i

Brand: Canon Pages: 1556

Brand: IDStation Pages: 18

Brand: Parkside Pages: 104

Digital Color Press 700

Brand: Xerox Pages: 216

C5020N - FS Color LED Printer

Brand: Kyocera Pages: 410

BradyPrinter A5500

Brand: Brady Pages: 72

Brand: Xerox Pages: 109

Brand: Paradise POS Pages: 275

ThermalTronix TT-1025EX-MIL

Brand: Intellisystem Pages: 11

Brand: IBM Pages: 2

Brand: Ricoh Pages: 88

Brand: SATO Pages: 241

Brand: Infinite Peripherals Pages: 29

Brand: WOOSIM Pages: 24

Brand: D3D Pages: 6

Brand: Malyan Pages: 41

Brand: Sinfonia Technology Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands