Fuji Imvac BT-86EI Operator'S Manual Download Page 9

Problem:

 

The idle is not steady.

Solution:

 

Your low-speed needle “L” valve is too rich. Close it 1/8 turn and try again.

C. High-Speed Adjustment:

The high-speed rpm and transition performance is adjusted with the high-speed 
“H” needle valve. When adjusting, turn the screw about 1/8 of a turn each time. 
The position of the “H” needle will vary according to air temperature and field 
elevation. If your engine is running smoothly, then do not adjust this needle valve. 
Follow the recommended procedures if any of the following happens:

Problem:

 

1.

 Engine stops at full throttle.

 

2.

 Engine hesitates when accelerated rapidly.

 

3.

 The engine will not come up to full Rpm at full throttle.

Solution:

 

Your high-speed needle valve “H” is too lean. Open it 1/8 turn and try again.

Problem:

 

1. 

Your engine does not reach full rpm.

 

2. 

Carbon build-ups appear consistently on your spark plug.

Solution:

 

Your high-speed needle valve “H” is too rich. Close it 1/8 turn and try again.

3-Year Limited Warranty For USA and Canada

Fuji-Imvac warrants this product to be free from defects in materials and workmanship for a period of three (3) years 
from the date of purchase. During that period, Fuji-Imvac will, at its option, repair or replace without service charge 
any product deemed defective due to those causes. You will be required to provide proof of purchase date (receipt 
or invoice).

•  This warranty does not cover damage caused by crash, abuse, misuse, alteration or accident. Damage caused by 

customer disassembly, tampering, use of substandard fuel, use of incorrect accessories (spark plug, prop, etc.) or 
any use of the engine for which it is not specifically intended will automatically void the warranty of the engine. If 
there is damage resulting from these causes within the stated warranty period, Fuji-Imvac will, at its option, repair 
or replace it for a service charge not greater than 50% of the current retail list price. Be sure to include your daytime 
telephone number and e-mail address in case we need to contact you about your repair.

•  Under no circumstances will the purchaser be entitled to consequential or incidental damages. This warranty gives 

you specific legal rights and you may also have other rights, which vary from state to state.

•  If you attempt to disassemble or repair this unit yourself, it may void the warranty.

For service on your Fuji-Imvac engine, either in or out of warranty, send it postpaid and insured to:

Hobby Services

3002 N. Apollo Dr., Suite #1

Champaign, IL  61822 USA

(217) 398-0007

www.hobbyservices.com

Along with your engine and proof of purchase date, please include a complete written explanation detailing the 
problem(s). State your name and address clearly. For repairs not covered under warranty, you must specify whether 
you wish the charges to be billed COD or if you wish to be notified of the charges so you can send a check.

Outside USA and Canada, contact local importer for warranty information.

9

Summary of Contents for BT-86EI
















Reviews: