FTS LYOSTAR 3 Operator'S Manual Download

Page: 38 / 82

Sample Extractor Assemblies

FTS Systems LyoStar™ 3

Rev 006, 01/14

Sample Extractor Installation

Standard Door Removal

Before installing the Sample Extractor Assembly, the standard acrylic door must be
removed from the freeze-dryer.

Ensure that the unit is not in operation and that the product chamber is not

under vacuum.

Open the product chamber door. Have an assistant in position to support the

door.

Remove the upper and lower quick release pins from the hinge assembly, and

remove the standard door.

Sample Extractor Installation

Prepare the Sample Extractor Assembly door for installation by unscrewing

and removing both thumbscrews from the front panel.

Remove the front antechamber plate and selector arm.

Quick Release Pins

Thumbscrew

Summary of Contents for LYOSTAR 3



















































































Search results

Summary of Contents for LYOSTAR 3

Reviews:

Related manuals for LYOSTAR 3

Brands by name

Popular brands

FTS LYOSTAR 3, Operator'S Manual

Search results

Summary of Contents for LYOSTAR 3

Reviews:

Related manuals for LYOSTAR 3

Brands by name

Popular brands