background image

8

SPECIFICATIONS - Models 20 thru 75

Description

Model

20

25

35

50

75

Operating Conditions 

Rated Capacity
@125 psig, 8.8 kgf/cm

2

*

scfm
m

3

/min

60 / 50 Hz
60 / 50 Hz

20 / 17

0.57 / 0.48

25 / 21 

0.71 / 0.59

35 / 27 

0.99 / 0.76

50 / 50 

1.42 / 1.42

75 / 61

2.12 / 1.7

Maximum Working Pressure

250 psig (17.6 kgf/cm

2

)

Maximum Inlet Temperature

180°F (82°C)

Min/Max. Ambient Temperature

40-110°F (4-43°C)

Pressure Drop @
rated capacity

psi
(kgf/cm

2

)

60 / 50 Hz
60 / 50 Hz

4.5 / 2.9

(0.32 / 0.20)

3.3 / 2.4

(0.23 / 0.17)

4.7 / 2.9

(0.33 / 0.20)

4.5 / 4.5

(0.32 / 0.32)

3.8 / 2.2

(0.27 / 0.15)

Refrigeration System Data

Compressor Type

 

Hermetic, Rotary, Permanent Split Capacitor

BTU/HR - Refrigeration Only
@ ASRE-T Conditions  

60 / 50 Hz

8720 / 7043

12500 / 9970

Outlet Air Temperature
  (nominal @ rated conditions)

155°F (68°C)

Refrigerant Type

R-407C

Refrigerant Charge

oz (grams) 

60 / 50 Hz

See Dryer Serial Tag

Suction Pressure Setting

67 psig (4.7 kgf/cm

2

Factory Test (design) Pressure
  high side/low side

330/178 psig (23.2/12.5 kgf/cm

2

Condenser Fan Switch Setting (in-out) 

240-180 psig (16.9-12.7 kgf/cm

2

Air Flow Across Condenser

cfm
m

3

/min

60 / 50 Hz
60 / 50 Hz

280 / 235
(7.9 / 6.7)

620 /515

(17.6 / 14.6)

Electrical Data

Unit
VAC/phase/Hz

115/1/60

115/1/60

  Minimum/maximum volts

98-127

  Full Load AmpS (FLA)

8.7

12.6

  Branch Circuit Fuse Size (amps)

15

20

Compressor
  Volts/phase/Hz

115/1/60

  Rated Load amps (RLA)

7.5

11.0

  Locked Rotor amps (LRA)

44.0

67.0

  Watts (input)

853

1220

  Overload (External)

Thermal and Current (Auto Reset)

Condenser fan motor
  Volts/phase/Watts (output)

115/1/25

115/1/35

  Full Load Amps (FLA)

1.2

1.6

Unit
  VAC/phase/Hz

220-240/1/50

220-240/1/50

  Minimum/maximum volts

198-264

  Full Load Amps (FLA)

3.4

6.0

  Branch Circuit Fuse Size (amps)

15

Compressor
  Volts/phase/Hz

220-240/1/50

  Rated Load amps (RLA)

2.8

5.1

  Locked Rotor amps (LRA)

18.6

28.0

  Watts (input)

690

990

  Overload (External)

Thermal and Current (Auto Reset)

Condenser fan motor
  Volts/phase/Watts (output)

220-240/1/18.3

220-240/1/25.6

  Full Load Amps (FLA)

0.6

0.8

*  Capacity @ 180°F, 82°C inlet temperature, 160°F, 71°C inlet pressure dew point,   95°F, 35°C ambient temperature, 50°F, 10°C outlet pressure dew 

point, and less than 5 psi, 0.35 kgf/cm

2

 pressure drop.

Summary of Contents for RNH100

















Reviews: