Frontier ST0320 Operator'S Manual Download Page 12

OPERATION

12

MTF-041007C

BEFORE STARTING THE ENGINE

WARNING: Experiences indicates that alcohol

blended fuels (called gasohol or those using

ethanol or methanol) can attract moisture

which leads to separation and formation of acids dur-

ing storage.  Acidic gas can damage the fuel system

of an engine while in storage.

NOTE: To avoid engine problems, the fuel system

must be emptied before storage for 30 days or longer.

Start the engine and let it run until the fuel lines and

carburetor are empty.  Use the carburetor bowl drain

to empty residual gasoline from the float chamber.

Use fresh fuel next season.  See the Storage section in

this manual for additional information.

Never use engine or carburetor cleaner products in the

fuel tank or permanent damage can occur.

HOW TO MIX THE FUEL MIXTURE

The two cycle engine, used on this snow thrower, requires

a mixture of gasoline and oil for lubrication of the bearings

and other moving parts. The correct fuel mixture ratio is

50:1 (2.6 oz. oil per  one gallon of gas - see the Fuel Mix-

ture Chart). Gasoline and oil must be pre-mixed in a clean

gasoline container. Always use fresh, clean, unleaded gas-

oline.

FUEL MIXTURE CHART (mixture 50:1)

U.S.

IMPERIAL

   SI. (Metric)

GAS

OIL

GAS

OIL

GAS

OIL

1 Gal.

2.6

oz.

1 Gal.

3.1 oz.

liter

80

ML

Mix gasoline and oil as follows:

1. Pour one (1) U.S. quart of fresh, clean, unleaded auto-

motive gasoline into a one gallon size gasoline con-
tainer.

2. Add 2.6 ounces of clean, high quality, two-cycle oil to

the gasoline container.

IMPORTANT: Do not use outboard motor oil or

multi-viscosity oils,such as 10W-30 or 10W-40.

3. Install the fuel cap onto the gasoline container. Vigor-

ously shake the gasoline container  to mix the oil with
the gasoline.

4. Add an additional three (3) U.S. quarts of gasoline to

the gallon container. Again shake the gasoline contain-
er.

WARNING: Gasoline is flammable. Always use

caution when handling or storing gasoline.

Do not fill fuel tank while snow thrower is run-

ning, when it is hot, or when snow thrower is in an

enclosed area.

Keep away from open flame or an electrical spark and

do not smoke while filling the fuel tank.

Never fill the tank completely.  Fill the tank to within

1/4”-1/2” from the top to provide space for expansion

of fuel.

Always fill fuel tank outdoors and use a funnel or

spout to prevent spilling.

Make sure to wipe up any spilled fuel before stating

the engine.

Store gasoline in a clean, approved container and

keep the cap in place on the container.

Do not fill the fuel tank with gasoline that does not have oil mixed in it.  Shake the gasoline container before

each filling of the fuel tank.

Shake Can

OIl 

(2.6 oz.)

Gasoline

1U.S.

Quart

1 U.S. Gallon container

1 U.S.

Gallon

Special

Gasoline

Add more gas

(3 U. S. Quarts)

Figure 8

Summary of Contents for ST0320





































Reviews: