Frontier MS2342 Operator'S Manual Download Page 16

Page: 16 / 84

WHEELS & TIRES

The Manure Spreader may be shipped without the wheels/tires installed.

1. Assemble the Manure Spreader and check for proper assembly and adjustment. Make sure that

all bolts are tightened.

2. Attach the wheels with tires, using the lug nuts furnished and torque the mounting hardware to

the appropriate torque listed in the Service Chapter. Check wheel bolts periodically thereafter.

3. Inflate the tires to the appropriate pressure listed in the Service Chapter.

4. Check the Manure Spreader for proper assembly and adjustment and make sure that all bolts

are tightened.

5. Securely retighten after a few hours of operation, as bolts can loosen up on new machinery.

6. Lubricate the Manure Spreader completely.

SET-UP & ASSEMBLY

-14-

NOTE:

Determine right or left side of the Manure Spreader by viewing it from the rear. If instructions

or parts lists call for hardened bolts, refer to bolt torque chart.

Summary of Contents for MS2342





















































































Search results

Summary of Contents for MS2342

Reviews:

Related manuals for MS2342

Brands by name

Popular brands

Frontier MS2342, Operator'S Manual

Search results

Summary of Contents for MS2342

Reviews:

Related manuals for MS2342

Brands by name

Popular brands