Fronius Datamanager 2.0 Operating Instructions Manual Download Page 12

Page: 12 / 88

Unless otherwise expressly permitted by the manufacturer, changes or modifications to
the wireless module are not allowed and lead to a loss of the right of use of the device by
the user.

Scope of Supply

Fronius Datamanager 2.0 plug-in card

1 x Fronius Datamanager 2.0 plug-in card

1 x Fronius Solar Net termination plug

1 x 16-pin plug

1 x FCC sticker label, three parts

Additional equipment depending on the inverter:

1 x antenna

1 x Fronius Solar Net termination
plug

Fronius Galvo
Fronius Symo
Fronius Primo

1 x antenna

1 x 1 m RG58 antenna cable

1 x mounting bracket

1 x double-sided adhesive tape

Fronius IG
Fronius IG Plus
Fronius IG Plus V

1 x antenna

1 x 3 m RG58 antenna cable

1 x mounting bracket

1 x double-sided adhesive tape

Fronius IG 300 - 500
Fronius CL
Fronius CL - USA

1 x antenna

1 x 0.4 m RG58 antenna cable

1 x 3/4 in. screw joint

1 x 3/4 in. hex nut

1 x 3/4 in. seal

Fronius IG 2000 - 5100 - USA
Fronius IG Plus - USA
Fronius IG Plus V - USA

Fronius Datamanager Box 2.0

1 x Fronius Datamanager Box 2.0 with wall bracket

2 x Fronius Solar Net termination plugs

1 x 16-pin plug

1 x antenna

1 x 3 m RG58 antenna cable

1 x mounting bracket

1 x double-sided adhesive tape

2 x installation a screws

1 x "DATCOM Cabling" leaflet

Using the Sticker
Labels

IMPORTANT!

If the three-part sticker label included in the scope of supply for the

Datamanager 2.0 has not already been affixed to the inverter at the factory, this must be
done now.

Position of the sticker label on the inverter:

Summary of Contents for Datamanager 2.0

























































































Search results

Summary of Contents for Datamanager 2.0

Reviews:

Related manuals for Datamanager 2.0

Brands by name

Popular brands

Fronius Datamanager 2.0, Operating Instructions Manual

Search results

Summary of Contents for Datamanager 2.0

Reviews:

Related manuals for Datamanager 2.0

Brands by name

Popular brands