Froling RBG 3200 Touch Operating Instructions Manual Download

Page: 5 / 41

2 Installation

❒ Run the bus cable through the large grommet
❒ Fit the holding frame as shown at the desired position in the room using the

anchors and screws provided

➥ The large grommet must be on the right!
➥ It is recommended to install the device above a flush-mounted socket so that

there is plenty of space to stow away the bus cable.

2.1 Initial start-up

NOTICE

You should have the initial startup carried out by the authorised heating engineer
from Froling customer services.

2.1.1 Connecting the bus cable

For the bus connections between the individual modules, cable type
LIYCY paired 2x2x0.5 should be used. The connection to the 5-pin plugs should be
carried out according to the following diagram:

BUS

CAN H

CAN L

BUS

CAN H

CAN L

Braided shield

White

Green

Yellow
Brown

Braided shield

White

Green
Yellow
Brown

Installation

Initial start-up

Operating Instructions RBG 3200 Touch | B0780115_en

Summary of Contents for RBG 3200 Touch










































Search results

Summary of Contents for RBG 3200 Touch

Reviews:

Related manuals for RBG 3200 Touch

Brands by name

Popular brands

Froling RBG 3200 Touch, Operating Instructions Manual

Search results

Summary of Contents for RBG 3200 Touch

Reviews:

Related manuals for RBG 3200 Touch

Brands by name

Popular brands