Froling RBG 3200 Touch Operating Instructions Manual Download | Manualshive

Page: 30 / 41

background image

5.6 Difference regulator

5.6.1 Difference regulator - Status

System menu

Diff. control

Heat source sensor

27°C

Display of the current heat source temperature of the differential controller (e.g. tiled stove with water pock‐
et, ...)

Heat sink sensor

40°C

Display of the current temperature of the heat sink for the differential controller (e.g. layered tank, ...)

Pump speed

0%

Specifies the current speed of the differential controller pump.

5

Menu overview and parameters

Difference regulator

30

Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

«
...
28
29
30
31
32
...
»

Summary of Contents for RBG 3200 Touch










































Reviews:

No comments

Related manuals for RBG 3200 Touch

Brand: ZEHUS Pages: 28

Brand: Valfonta Pages: 12

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 11

Brand: Nauticam Pages: 2

Brand: National Instruments Pages: 18

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 20

GEMINI C Series

Brand: NAPCO Pages: 24

Brand: Panamax Pages: 16

Brand: Valcom Pages: 6

Brand: FEAS Pages: 4

Brand: Apricus Pages: 32

Brand: Case IH Pages: 81

Brand: ISVT Pages: 78

Brand: Linear Technology Pages: 8

Brand: Precision Pages: 8

TRAP-SHUFFLE Game Simulator

Brand: RF SOLUTIONS Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands