Fröling GAR 110 Installation And Operating Instructions Manual Download Page 42

Page: 42 / 48

6.1 Maintenance work by the operator

❒

Regular maintenance of the discharge extends the service life of the entire plant
and is a basic requirement for trouble-free operation!

W = weekly, M = monthly, Q = quarterly, F = prior to each fill of the store

No.

Component

Int.

Operation

Motor / gears

❒

Carry out a general visual inspection of the drive
motor

➥

No major oil leaks should be visible.

Gravity shaft / safety
switch

Function test of the safety switch:

❒

Open the inspection cover of the gravity shaft

➥

The system should switch off immediately.

❒

Check the inlet area for material build-up and clean
where necessary.

❒

Close gravity shaft cover

❒

Check fault message on the controller

Sprinkler system

Sprinkler system ready for operation

❒

Check the position of the sensor

❒

Visual inspection of the sensor and the capillary
tube

❒

Check water supply for sufficient pressure

Spring piles

❒

Check that the connecting screws of the clamping
plate are firmly in position and tighten if necessary

➥

Replace broken screws immediately

❒

Check that the connections of the spring piles have
a little play (approx. 1mm)

➥

Tighten or loosen the screws if necessary

Clamping plate of the
spring piles

❒

Check that the screws of the clamping plate are
firmly in position and tighten if necessary

Servicing the system

Maintenance work by the operator

Fröling Ges.m.b.H. | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

Summary of Contents for GAR 110

















































Search results

Summary of Contents for GAR 110

Reviews:

Related manuals for GAR 110

Brands by name

Popular brands

Fröling GAR 110, Installation And Operating Instructions Manual

Search results

Summary of Contents for GAR 110

Reviews:

Related manuals for GAR 110

Brands by name

Popular brands