Fröling GAR 110 Installation And Operating Instructions Manual Download Page 33 | Manualshive

Page: 33 / 48

background image

4.4 Connecting the system

4.4.1 Electrical connection

DANGER

When working on electrical components:

Risk of electrocution!

When work is carried out on electrical components:

❒

Always have work carried out by a qualified electrician

❒

Observe the applicable standards and regulations

➥

Work must not be carried out on electrical components by unauthorised
persons

❒

Lay cables of components to control cabinet

➥

Lay the cables so that nobody will trip over them!

➥

Do not lay the cable over or around sharp edges!

❒

Wire the connections according to the wiring diagram

4.4.2 Connecting the sprinkler system

Connection should only be carried out by authorised technicians.

When connecting the sprinkler system, please also note:

❒

Put a stopcock and bolted joint in front of the thermal discharge safety device

➥

Important for easy dismantling in the event of maintenance work!

Assembly

4

Connecting the system

Installation and Operating Instructions GAR 110 / 150 | M2060120_en

33

«
...
31
32
33
34
35
...
»

Summary of Contents for GAR 110

















































Reviews:

No comments

Related manuals for GAR 110

Brand: YSI Pages: 70

Brand: jcb Pages: 41

Brand: CAMAG Pages: 40

PowerXL DX-NET-ETHERNET2-2

Brand: Eaton Pages: 48

Power Xpert C445

Brand: Eaton Pages: 2

Brand: Hantek Pages: 124

Brand: Hameg Pages: 10

Brand: Baileigh Industrial Pages: 12

Brand: Easylife Pages: 3

Brand: York Pages: 32

Brand: MAKSIWA Pages: 155

Brand: Feniex Pages: 5

Brand: Lites Pages: 8

Brand: Taylor Pages: 82

Brand: Tascam Pages: 100

Firefly Low Voltage Lighting System

Brand: Ultra Pages: 2

Brand: Lumination Pages: 2

Brand: Mindray Pages: 165

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands