Fritz! Box 6490 cable Installation And Operation Manual Download Page 36

Page: 36 / 173

FRITZ!Box 6490 Cable

Connecting ISDN Telephones and ISDN Terminal Devices

9.2

Connecting ISDN Telephones and ISDN Terminal Devices

Requirements

•

ISDN terminal devices must support operation on an
ISDN point-to-multipoint line.

Connecting an ISDN Telephone

Connect the ISDN telephone to the “FON S

” port.

Configure the ISDN telephone in the FRITZ!Box; see

page 40

Connecting Multiple ISDN Telephones

With S

bus cabling you can connect up to eight ISDN tele-

phones to the FRITZ!Box. Please note for configuration:

•

Since the FRITZ!Box has terminators installed, the
FRITZ!Box must be positioned on one end of the S

bus

cabling.

•

The FRITZ!Box can supply one ISDN telephone with elec-
trical power. All other ISDN telephones will need their
own power supply.

FON 1

N 2

FON 2

N 1

LAN 1

LAN 2

LAN

LAN 3

LAN

LAN 4

Power

FON S

WLA

Info

WLAN

DECT

Fon

Power/Cable

CABLE

Summary of Contents for Box 6490 cable














































































































































































Search results

Summary of Contents for Box 6490 cable

Reviews:

Related manuals for Box 6490 cable

Brands by name

Popular brands

Fritz! Box 6490 cable, Installation And Operation Manual

Search results

Summary of Contents for Box 6490 cable

Reviews:

Related manuals for Box 6490 cable

Brands by name

Popular brands