background image

IMPORTANT - PLEASE READ
AND FOLLOW

THIS BUILT-IN KIT IS DESIGNED FOR USE ONLY
WITH ELETROLUX MICROWAVE OVENS SPECI-
FYING BUILT-IN KIT

MWTRMKT27 OR MWTRMKT30 ON THE RATING
LABEL ON THE LEFT SIDE WALL OF THE
MICROWAVE OVEN CAVITY.

IF YOUR LOWER CONVENTIONAL OVEN IS NOT
LISTED IN THE USE AND CARE MANUAL OF THE
MICROWAVE OVEN, THEN DO NOT INSTALL THE
MICROWAVE OVEN ABOVE IT OR IN ANY AREA
WHERE HEAT AND STEAM ARE GENERATED; FOR
EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL
RANGE.

Installation
Instructions

Built-in Trim Kit

MWTRMKT27 and MWTRMKT30

P/N 316137335

TINSEB384MRR0

BEFORE YOU BEGIN

IMPORTANT

– Save these instructions 

for local inspector's use.

IMPORTANT

– Observe all governing 

codes and coordinates.

Note to Installer

– Be sure to leave these

instructions with the Consumer. 

Note to Consumer

– Keep these 

instructions for future reference.

Skill level

- Installation of this appliance requires 

basic mechanical and electrical skills.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

Unplug the microwave oven before attempting
installation of this kit.

Because the kit includes metal parts, caution
should be used in handling and installation to
avoid the possibility of injury.

Do not remove permanently affixed labels, warn-
ings, or plates from the product. This may void
the warranty.

Read

these instructions completely and carefully. 

QUESTIONS?

For customers in the United States call: 1-800-944-9044 

For customers in Canada call: 1-800-213-9397 (English) 
1-800-668-4606 ext.8199 (French)

Visit our Website at: 

www.frigidaire.com

READ CAREFULLY.
KEEP THESE INSTRUCTIONS.

FOR YOUR SAFETY:

WARNING

– Before beginning the installation,

switch power off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service disconnect-
ing means cannot be locked, securely fasten a promi-
nent warning device, such as a tag, to the service
panel. 

1

Summary of Contents for GLMB209D













Reviews: