background image

1

MICROWAVE/ WALL OVEN COMBINATION

INSTALLATION INSTRUCTIONS

B

A

D

F

I

H

G

11½”

(29.2 cm)

11½”

(29.2 cm)

1¼”
(3.2 cm)
Min.

1¼”
(3.2 cm)
Min.

3” (7.6 cm)

Max.

3” (7.6 cm)

Max.

1” (2.5 cm)

Min.

1” (2.5 cm)

Min.

40-15/16”
(104 cm)

40-15/16”
(104 cm)

C

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

 FOR YOUR SAFETY:  Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

Your new wall oven has been designed to fit a limited variety of cutout sizes to make the job of installing
easier. The first step of your installation should be to measure your current cutout dimensions and
compare them to the cutout dimensions chart below for your model. You may find little or no cabinet
work is necessary.

P/N 318201521 (0503) Rev. A

English – pages 1-6

Español – páginas 7-12

All dimensions are stated in inches and (cm).

 Do not remove spacers (if equipped) on the side walls and/or on the back of the built-in

oven. These spacers center the oven in the space provided. The oven must be centered to prevent
excess heat buildup that may result in heat damage or fire.

2" (5 cm) Wide Wood

Spacer if Needed

PRODUCT DIMENSIONS

CUTOUT DIMENSIONS AND CABINET WIDTH

Min.    F   Max.

Min.    H   Max

.

MODEL

27" (68.6 cm) Wall Oven

30" (76.2 cm) Wall Oven

MODEL

27" (68.6 cm) Wall Oven

30" (76.2 cm) Wall Oven

A

27 (68.6)

30 (76.2)

B

42¾ (108.6)

42¾ (108.6)

G (Min.)

23½ (59.7)

23½ (59.7)

C

24

5

/

8

 (62.5)

28¼ (71.8)

D

24½ (62.2)

24½ (62.2)

I

27

1

/

8

 (68.9) Min

30

1

/

8

 (76.5) Min

24

7

/

8

 (63.2)

28½ (72.4)

25¼ (64.1)

29 (73.7)

41

1

/

8

  (104.5)

41

1

/

8

  (104.5)

41¼ (104.8)

41¼ (104.8)

NOTES:
1.

Base must be capable of supporting 225 pounds (102 kg).

2. 

 Allow at least 21" (53.3 cm) clearance in front of oven for door
depth when it is open.

3.

Dimension

 G 

(cutout depth)

 

is

critical to the proper installation of
the built-in oven.  If the oven
decorative trim does not butt
against the cabinet verify
dimension 

G

 to assure it is the

required depth.

Door Open
(see note 2)

Spacer

Electrical

Junction Box

(right or left side)

Hole for
Cable
(right or
left side
depending
on model)

* Suggested distance from floor

is 11½" (29.2 cm).
Minimum required distance is 4
½" (11.4 cm)

Figure 1

Printed in United States

Summary of Contents for GLEB27M9FB - 27 Inch Microwave Combination Oven













Reviews: