background image

4

 To reduce risk of fire or serious injury to persons or property, comply with the

basic warnings listed in 

Important Safety Instructions

  and those listed below.

Before cleaning the dryer interior, 

unplug the electrical power cord

 to avoid electrical

shock hazards.

Do not use any type spray cleanser when cleaning dryer interior. Hazardous fumes or
electrical shock could occur.

Inside

Clean the lint screen after every load. Lint build-up in the screen restricts air flow, which
causes longer drying times. The screen is located at the bottom of the door opening.
Remove by pulling straight up. Remove the lint and replace the screen.

Occasionally a waxy build-up may form on the lint screen from using dryer-added fabric
softener sheets. To remove this build-up, wash the lint screen in warm, soapy water. Dry
thoroughly and replace. Do not operate the dryer without the lint screen in place.

If the dryer drum becomes stained from noncolorfast fabrics, clean the drum with a damp
cloth and a mild liquid household cleanser. Remove cleanser residue before drying the
next load.

Every 18 months an authorized servicer should clean the dryer cabinet interior and
exhaust duct. These areas can collect lint and dust over time. An excessive amount of
lint build-up could result in inefficient drying and possible fire hazard.

Outside

Clean the cabinet with mild soap and water. 

Never use harsh, gritty or abrasive

cleansers.

If the cabinet becomes stained, clean with diluted chlorine bleach [1/2 cup
(120 ml) in 1 quart (.95 liter) water]. Rinse several times with clear water.

Remove glue residue from tape or labels with a mixture of warm water and mild
detergent. Or, touch residue with the sticky side of the tape or label.

Before moving the dryer

, place a strip of cardboard or thin fiberboard under the  front

leveling legs to prevent damage to floor.

PROBLEM

PROBLEM

PROBLEM

PROBLEM

PROBLEM

• Add a few bath towels to small loads for

proper tumbling.

• Some "silk-like" fabrics should be air dried.
• Use proper drying temperature.
• Place fabric softener sheet on top of load

before starting the dryer.

• Do not overload dryer.
• Use fabric softener in washer or dryer to

reduce static electricity.

• Remove items when they are slightly damp to

avoid overdrying.

• Check that lint screen is clean and in place.

• Use fabric softener to lubricate fibers.
• When ironing, use spray starch or fabric finish

on collars and cuffs.

• Turn items inside out to reduce abrasion.

• Follow fabric care label directions.
• If shrinking is a concern, check load often.
• Remove items while slightly damp and hang or

lay flat to complete drying.

• Block knits into shape.

• Do not overload dryer.
• Remove items as soon as cycle ends.

PREVENTIVE MEASURES

PREVENTIVE MEASURES

PREVENTIVE MEASURES

PREVENTIVE MEASURES

PREVENTIVE MEASURES

Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory drying results,
follow these suggestions provided by The Soap and Detergent Association.

Common Drying Problems

Greasy, oily
stains

Lint

Pilling

(Fibers break off,
ball up and cling
to fabric.)

Shrinking

Wrinkling

POSSIBLE CAUSES

POSSIBLE CAUSES

POSSIBLE CAUSES

POSSIBLE CAUSES

POSSIBLE CAUSES

• Fabric softener sheet.

• Overloading.
• Overdrying causes static

electricity.

• Lint screen not clean when

cycle began.

• Lint is attached to "pills."

• Pilling is normal with

synthetic and permanent
press fabrics. This is due to
abrasion from normal wear.

• Overdrying.

• Overloading.
• Leaving items in dryer after

cycle ends.

SOLUTIONS

SOLUTIONS

SOLUTIONS

SOLUTIONS

SOLUTIONS

• Rub fabric softener stains with bar soap.

Rinse and rewash.

• Reduce load size and rewash using liquid

fabric softener in the final rinse.

• Or, add a fabric softener sheet and tumble

without heat.

• Use lint brush or roller to remove lint.

• Use a lint brush or shaver to remove pills.

• Irreversible condition.

• Reduce load size and tumble at medium or

low heat for 5-10 minutes.

• Remove items immediately. Hang or fold.

Care and Cleaning

Clean lint screen after every load.

Do not store or place laundry products
on top of dryer at any time. They can
damage the finish or controls.

Summary of Contents for FEQ332ES0







Reviews: