background image

5

Using Air Conditioner

To reduce the risk of fire, electric shock, or injury to persons, read

the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

To begin operating the air conditioner, follow these steps:

1. Plug in the air conditioner. (To prevent electrical hazards, do not use an extension

cord or an adapter plug.)

2. Set the thermostat to the highest number (coldest or cooler setting).

3. Set the selector control to the highest COOL setting.

4. Adjust the louvers for comfortable air flow (see Air Directional Louvers).

5. Once the room has cooled, adjust the thermostat to the setting you find most

comfortable.

Review the “Air Conditioner Features” section for other settings.

NOTE:

If the air conditioner is turned off,

wait 3 minutes before restarting. This
allows pressure inside the compressor to
equalize. Failure to follow these
instructions may cause inefficient
operation.

 

             

The 

"Min. Cool"

 setting should be

 selected when minimum cooling is desired.

  

The 

"Hi. Fan"

 setting should be selected when maximum air circulation without  

The 

"Low. Fan" 

setting should be selected when minimum air circulation without  

 

 

             

 

Selected the "Fan Mode" automatically stops the compressor from running. 

 

 

              

 

The thermostat is used to set the desired room temperature when the unit is 
being operated in the 

"Cooling Mode"

.

To set the desired room temperature, rotate the thermostat switch to the 
desired setting. After the set temperature is achieved the thermostat will auto-

 

              

 

Rotate the thermostat selector clockwise for higher cool settings. Higher cool   
settings will provide lower room temperature.
Rotate the thermostat selector 

counter 

clockwise for lower cool settings.  

low cool

 

settings will provide higher room temperature.

 

              

 

 

matically start and stop the compressor in order to maintain the desired set 
temperature.

 

              

C

ool

 Mode

The desired cool setting is selected by rotating the selector knob to the appropriate
location

The 

"Max. Cool"

 

setting should be 

selected when maximum cooling is desired. 

 

 

              

cooling is desired.
 

 

 

              

cooling is desired.
 

 

Air Conditioner Features 

The controls featured in this manual are representational of the many models
available. Your model may offer slightly different features.

 

 

 

              

Thermostat (some models)

 

 

 

              

Fan Mode

 

 

Summary of Contents for FAA052N7A








Reviews: