background image

27

SETTING OVEN CONTROLS

How the Electronic Surface Element Controls 

work when the Sabbath feature is ON.

When  your  Oven  Sabbath  feature  is  ON,  the  Electronic 

Surface  Elements  are  also  in  Sabbath  mode.  This  means 

that  all  electronic  surface  element  control  displays  show 

Sb

”. The surface elements can be used even if the Sabbath 

Feature is on.

To turn ON a Surface Element when the Oven Sabbath 

Feature is active:

If you turn on a surface element when the oven Sabbath 

feature is on, the electronic surface element control will record 

that request and execute it with a 15-30 seconds delay. So 

the element will start heating 15-30 seconds after the surface 

element  control  was  turned  on.  As  the  oven  control,  the 

surface element display will not show the setting because 

Sb

” is on in the displays. When necessary, it is possible to 

adjust the power of the surface element but you have to 

remember that the surface element control will adjust the 

temperature with the same delay.

To  turn  OFF  the  Surface  Element  when  the  Oven 

Sabbath Mode is active:

To shut off the surface element while the Sabbath feature 

is ON, proceed as usual but take note that the element will 

immediately turn off without any delay.

SETTING THE SABBATH FEATURE

 

(for use on 

the Jewish Sabbath & Holidays)
The 

BAKE  TIME

  and

  DELAY  START 

pads  are  used  to 

set the Sabbath feature. The Sabbath feature may only be 

used with the 

BAKE

 pad. The oven temperature may be 

set higher or lower after setting the Sabbath feature (the 

oven temperature adjustment feature should be used only 

during Jewish Holidays), however the display will not visibly 

show or provide any audible tones indicating whether the 

change occurred correctly. Once the oven is properly set 

using Bake with the Sabbath feature active, the oven will 

remain continuously ON until cancelled. This will override 

the factory preset 6-Hour Energy Saving feature.
If the oven light will be needed during the Sabbath, press 

OVEN  LIGHT

    before  activating  the  Sabbath  feature. 

Once the oven light is turned ON and the Sabbath feature 

is active, the oven light will remain ON until the Sabbath 

feature is turned OFF. If the oven light needs to be OFF, 

be sure to turn the oven light OFF before activating the 

Sabbath feature.

IMPORTANT

It is not advised to attempt to activate any other program 

feature other than 

BAKE

 while the Sabbath feature is 

active. ONLY the following key pads will function after 

setting the Sabbath feature; 

0

 to 

9

BAKE

START

 & 

CANCEL

All other keypads

 should not be used once 

the Sabbath feature is properly activated.

NOTE

You may change the oven temperature once baking has 

started by pressing 

BAKE

, the numeric key pads for the 

temperature you want (example for 425°C press 

4 2 5

and  then  pressing 

START

 

twice

  (for  Jewish  Holidays 

only). Remember that 

the oven control will no longer 

beep or display any further changes

 once the oven 

is set for the Sabbath feature.

To Program the Oven to Begin Baking Immediately & 

activate the Sabbath feature 

(example: baking at 350°F)

1.  Be sure that the clock is set with the correct time of day.

2.  Place the food in the oven.

3.  Press 

UPPER OVEN

 or 

LOWER OVEN 

to select oven

.

4.  Press 

BAKE

. “

350°

” appears in the display.

5.  Press 

START

. The actual oven temperature appears in 

the display.

6.  If you desire to set the oven control for a 

Bake Time 

or 

Delayed Bake Time

 do so at this time. If not, skip 

this step and continue to step 8. Refer to the 

Bake 

Time / Delay Start 

section for complete instructions. 

Remember the oven will shut down after using 

Bake 

Time 

or 

Delay Start 

and therefore may only be used 

once during the Sabbath/Jewish Holidays. The maximum 

Delayed Start Bake

 time is 11 hours & 59 minutes.

7.  The oven will turn ON and begin heating.

8.  Press and hold both the 

BAKE TIME 

and

 DELAY START

 

pads for at least 

3 seconds

. “

SAb

” will appear in the 

display.  Once  “

SAb

”  appears  in  the  display  the  oven 

control will no longer beep or display any further changes 

and the oven is properly set for the Sabbath feature.

9.  The oven may be turned OFF at any time by fi rst pressing 

CANCEL

 pad (this will turn the oven OFF only). To turn 

OFF the Sabbath feature press and hold both the 

BAKE 

TIME 

and

 DELAY START

 pads for at least 

3 seconds

SAb”

 will disappear from the display.

Should you experience a power failure or interruption, the 

oven will shut off. When power is returned, “

SF

” (Sabbath 

Failure) will be shown in the oven display and the cooktop 

displays.  The  oven  and  cooktop  will  not  turn  back  on 

automatically.  If  your  food  was  nearly  fully  cooked,  you 

may allow the trapped heat in the oven to fi nish the cooking 

process. Otherwise, you should remove the food when the 

power failure occurs, because you may only start the oven 

once during the Sabbath/Jewish Holidays. After the Sabbath 

observance turn OFF the Sabbath feature and the oven may 

be used with all normal functions.
After the Sabbath observance turn OFF the Sabbath feature. 

Press and hold both the 

BAKE TIME 

and

 DELAY

 pads for at 

least 

3 seconds

. “

SAb

” will disappear from the display and 

the oven may be used with all normal functions. For further 

assistance, guidelines for proper usage, and a complete list 

of models with the Sabbath feature, please visit the web at 

http:\\www.star-k.org.

Summary of Contents for 318205204









































Reviews: