13
AUtOmAtIC ICE & WAtER DISPENSER (CONtINUED)
changing the Filter:
Water conditions vary throughout the world, but changing the
water filter every 6 - 9 months normally will ensure the highest
possible water quality.
Ice jams in the ice maker and/or hollow
ice cubes (partially frozen cubes with water inside), may also
be a sign that your water filter needs changing.
The
filter
Status
light will turn red after approximately 400 gallons of water
has flowed through the ice and water dispenser. Also, if the filter
has been in a refrigerator that has not been in use for awhile
(during moving for example), change the filter before reinstalling
the refrigerator. The dispenser system will also operate without
filtration (with filter cartridge removed and bypass installed).
PURESOURCE2
tm
* ICE AND WAtER fRONt
fILtER (SOmE mODELS)
Order new filter cartridges through the dealer where you
bought the refrigerator, contact the Electrolux Solutions Hotline
at 1-800-944-9044, or go to our web site at www.frigidaire.
com. It might be good to order some filter cartridges when
you first install your refrigerator. Be sure to ask for the FC-100
PureSource™* replacement cartridge.
system startup:
Water supply does not need to be turned off, however, do not
use ice and water dispenser while installing filter.
The filter cartridge has already been installed in the filter
housing at the factory. Refer to the How to Prime the Water
Supply System section to properly fill the system with water.
The PureSource2
TM*
Ice and Water Filter
System NGFC 2000 with the PureSource2
TM*
cartridge FC 100 is tested and certified by NSF
International, the nationally recognized and
respected, not for profit, certification organization
for public health safety. The PureSource2
TM*
Filter system is
tested and certified to ANSI/NSF Standards 42 and 53. See
performance data sheet for specifications. This system should
not be used on water that is microbiologically unsafe or with
water of unknown quality unless the water has been adequately
disinfected before or after traveling through the filtration system.
• Rated Capacity - 400 gallons
• Rated service flow - .5 GPM
• Maximum Rated Pressure - 100 PSI, Minimum 30 PSI
• Maximum Operating Temp. - 100°F, Minimum 33°F
to change filter:
It is not necessary to turn the water supply off to change the filter.
1
Turn OFF side mounted ice maker by raising wire signal
arm to the UP position. Turn OFF rear mounted ice maker
by pressing ON/OFF power switch to the “
O
” position.
2
Push the Filter Release Button, located to the right of
the filter cartridge, to release the filter from the housing.
To minimize the possibility of the filter falling out of the
housing during removal, it would be best to hold the
filter as it moves out toward you.
3
Pull the old filter cartridge straight out of the housing.
4
Discard the old filter.
5
Remove the new filter cartridge from the packaging.
Remove caps from filter and insert into the filter housing
the same way the old one came out.
6
When the cartridge is almost in, you will feel it stop
against the clip assembly in the back of the housing. The
clip assembly holds the filter cartridge firmly in place. At
this point, you will need to push firmly until the cartridge
snaps fully in place. When completely in place, the front
of the filter cartridge will be flush with the front of the
housing.
7
Turn ON side mounted ice maker by lowering wire signal
arm to the DOWN position. Turn ON rear mounted ice
maker by pressing ON/OFF power switch to the “
I
”
position.
8
Fill a glass with water. As you are doing this, check for
leaks at the filter housing.
9
to prime filter system and purge air from water line,
continue flushing the system for approximately 3 minutes
to assure that the purest water possible is stored in
the water tank.
there will be noticeable spurts and
sputters as the system pushes air out through the
system and out the dispenser nozzle. this is normal.
*
White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter.
NOtE
A small amount of water may be released during this
operation. You should have a paper towel or dish cloth
handy to wipe up any water that may drip out of the filter or
housing. Two small holes near the back of the housing have
been added for any excess water to escape. It would be
best to clear away any food near this area on the top shelf
in advance of removing the filter.
ImPORtANt
resetting the Filter status Light (some models)
After replacing the filter cartridge, it will be necessary to
press the Filter
Reset
button located on the ice and water
dispenser. This will reset the
filter Status
light. Push the
reset button until the green, red and amber lights flash
(10-15 seconds).
