Fridgmaster MTRL109A How To Use Manual Download Page 7

7

Changing the internal light

1

   Before carrying out the bulb replacement, always switch off and 

disconnect the electrical supply.

2

   Use a small screwdriver to undo the screw securing the lamp cover. 

3

   To remove the lamp cover, grasp the extended tab between thumb and 

forefinger and push gently toward the back of the cabinet.

4

   Remove the old bulb by unscrewing in an anti-clockwise direction.

5

   Replace with a new bulb (15w) by screwing it in a clockwise direction 

making sure that it is secure in the bulb holder.

6

   Replace the translucent light cover and re-secure with the screw 

before re-connecting your larder fridge to the electrical supply and 
switch on.

MAINTENANCE

The larder fridge is not working

Check it is plugged in and switched on. Check that the fuse in the plug 
has not blown. Plug in another appliance, such as a lamp, to see if the 
socket is working. 

Condensation appears on the outside of the  
larder fridge

This may be due to a change in the room temperature. Wipe off  
any residue of moisture. If the problem continues call the customer  
service department.

Noises

You may hear some unusual noises from time to time. See ‘Noises inside 
the larder fridge’ on page 5.

If you are not able to identify and eliminate the faults according to 
the above recommendations, contact the customer service department, 
advising the model number of the appliance which is shown on the back 
of the rating plate.

Do not attempt to repair your larder fridge yourself as it might endanger 
you and others.

Moving your larder fridge

Location

Do not locate your larder fridge or near a heat source, eg. cooker, boiler  
or radiator. Also avoid direct sunlight.

Levelling the larder fridge 

Make sure the larder fridge is level. Use the rotating levelling feet at  
the front. If the larder fridge is not level, the doors and magnetic seal 
alignments will be affected.

Do not turn on the larder fridge for two hours

After the larder fridge is in place it needs to be left for two hours.  
The coolant fluid needs time to settle. 

Installation

Don’t cover or block the vents or grilles of your appliance.

Servicing

Repairs and maintenance of the appliance should only be performed  
by an authorised, qualified technician.

TROUBLESHOOTING

FRIDGE MTRL109A D2.indd   7

26/3/08   09:59:44

Summary of Contents for MTRL109A













Reviews: