background image

4

ASSEMBLY INSTRUCTIONS

MOUNTING EXTRUSION TO TENT BASE

1.  You need to decide which orientation the roof top tent will open on 

your vehicle (refer to previous page). 

   If you decide your roof-top tent is to open off the rear of your 

vehicle then you will need to cut the bars as depicted in Diagram 1. 

   If you decide on the roof top tent opening to the side of your 

vehicle 

DO NOT

 cut the bars.

2. Place the tent and base on clean, level ground.

3.  Using four 6mm bolts and 6mm fender washers supplied, slide 

your hand in-between the base and mattress and then insert the 
bolts into the pre-drilled holes. See Diagram 2.

4. Place the mounting extrusions into position over the bolts.

5.  Slide the 6mm nuts into the mounting extrusions and tighten the 

bolts fi rmly from inside the tent.

6.  Mount the ladder to the base of the tent using 6mm bolts. Bolt 

each ladder bracket to the base of the tent through the pre-drilled 
holes see Figure 1. 

FITTING THE ROOF-TOP TENT TO ROOF RACKS 
OR ROOF BARS

1. Lift the tent onto the vehicle

2.  Place 1 x 8mm bolt into the slide plate. Slide the plate and bolt 

into the mounting extrusion. See Figure 2 & Diagram 2.

3.  Attach the roof-top tent to your roof rack or roof bars in four 

places. Use 2 bolts and 2 slide plates with the base plate to hold 
the bar. 1 set per corner, see Figure 3.

4.  Prior to tightening all the nuts, ensure that your roof-top tent is 

centred (side to side) on the roof of your vehicle and the mounting 
points (as far as possible) are symmetrically positioned near each 
corner of the tent.

Diagram 1

Figure 1

Figure 2

Figure 3

TENT BASE

ROOF RACK

6mm Stainless Steel Bolt

6mm Nut

6mm Fender Washer

Slide Plate with 8mm Stainless Steel Bolt

Base Plate

Aluminium Mounting Extrusion

6mm Fender Washer

Diagram 2

Summary of Contents for 933101









Reviews: