Freescale Semiconductor MSC8144E Reference Manual Download

Page: 445 / 1374

Programming Model

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

11-31

11.8.5 L2 ICache Tag State Register (L2IC_TAG)

This register is accessible only in L2 ICache debug mode.

Table 11-11 defines the L2IC_TAG bit

fields.

L2IC_TAG

L2 ICache Tag State Register

Offset 0x10

Bit

—

TVB

—

TAG

Type

Reset

Bit

TAG

Type

Reset

Table 11-11. L2IC_TAG Bit Descriptions

Name

Reset

Description

Settings

—

31–24

0xFF

Reserved. Write to ones for future compatibility.

TVB

Tag Valid Bit
Indicates whether the whole cache line is valid or
not.

Cache line not valid.

Cache line valid.

—

22–18

Reserved. Write to zero for future compatibility.

TAG

17–0

0x3FFFF

Tag
Indicates directly the status of the debugged TAG
according to a dedicated debug counter.

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MSC8144E

Reviews:

Related manuals for MSC8144E

Brands by name

Popular brands

Freescale Semiconductor MSC8144E, Reference Manual

Search results

Summary of Contents for MSC8144E

Reviews:

Related manuals for MSC8144E

Brands by name

Popular brands