manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at manualshive.com.

Share
Download
background image

L2 Instruction Cache

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

 

11-13

Note:

Port 2 of the CLASS initiator is disabled at reset and must not be enabled by the user 
(otherwise the interleaving between the two banks will not work). 

Do not disable the cache memory modules after they are enabled. To disable L2 
ICache operation, disable the L2 Cache window by clearing the L2IC_CEN[DEN] bit 
and then write start and end addresses of 0x000000 to L2IC_CSA and L2IC_CEA. 

If the cache is disabled after initialization, you must set the L2IC_CR2[CE] bit before 
setting the L2IC_CEN[DEN] bit to enable the cache.

11.4.6.2   L2 ICache Global Invalidation Command

The L2 ICache global invalidation command clears the valid bits in both cache modules in a 
single clock cycle. To execute a global invalidate, enter the sweep/invalidate command in the CC 
field and set the CGS bit in of L2IC_CR1 (see Section 11.8.2). The command also resets the 
PLRU machine. 

11.4.6.3   L2 ICache Global Lock Mode

To enter global lock mode, set the L2IC_CR2[CGL] bit (see Section 11.8.3). When globally 
locked, new data fetches are not written to the L2 ICache and no lines are trashed. Hit accesses 
are served as usual. Miss accesses are served without updating the cache memory. The PLRU 
machine is not updated while the L2 ICache is locked. The L2 ICache Global Lock mode may be 
useful to improve the performance of some applications that may be sensitive to interrupts, for 
example. After asserting this mode, all open miss accesses are served and updated as if L2 ICache 
is not globally locked. The lock mode disables only new miss data updates that are initiated after 
the L2 ICache enters global lock mode. 

The sweep operation overrides the global lock status. The value of the global lock bit is ignored 
during the cache sweep operation.

11.4.6.4   L2 ICache Partial Lock

L2 ICache can be partially locked to protect certain data. The lock is done in line resolution (16 
VBRs). The replace mechanisms are disabled for data that does not correlate with the active 
cache lock boundaries. In case of TAG match, the data of a locked line can be updated with new 
fetches to this line, but L2 ICache lines are not replaced. The locking is done in way boundaries. 

„

The reduced open boundaries contain 2 or 4 ways.

„

The exact partial lock configuration is programmed via dedicated register.

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Lanner NCA-4035 User Manual preview
NCA-4035
Brand: Lanner Pages: 109
Zonet ZUN2200 Quick Installation Manual preview
ZUN2200
Brand: Zonet Pages: 2
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Brand: National Instruments Pages: 36
Hama 00039747 Operating Instruction preview
00039747
Brand: Hama Pages: 6
Renesas REJ06B0734-0100 Application Note preview
REJ06B0734-0100
Brand: Renesas Pages: 19
Boss Vocal Performer VE-20 Owner'S Manual preview
Vocal Performer VE-20
Brand: Boss Pages: 20
Corsair LL140 RGB Series Manual preview
LL140 RGB Series
Brand: Corsair Pages: 30
B&B Electronics ESR901 User Manual preview
ESR901
Brand: B&B Electronics Pages: 90
Panasonic KX-W1000 Service Manual preview
KX-W1000
Brand: Panasonic Pages: 78
Acconeer XE132 Getting Started Manual preview
XE132
Brand: Acconeer Pages: 13
Renesas Direct Dummy IC M3T-DCT42B-450 User Manual preview
Direct Dummy IC M3T-DCT42B-450
Brand: Renesas Pages: 4
Johnson Controls Metasys NAE55 Installation Manual preview
Metasys NAE55
Brand: Johnson Controls Pages: 20
ETAS ETK-S6.0 User Manual preview
ETK-S6.0
Brand: ETAS Pages: 64
Tripp Lite SmartRack SR25UB Specification Sheet preview
SmartRack SR25UB
Brand: Tripp Lite Pages: 4
LAPIS Semiconductor ML7344 Quick Start Manual preview
ML7344
Brand: LAPIS Semiconductor Pages: 14
Talkswitch TALKSWITCH 24-CA Quick Manual preview
TALKSWITCH 24-CA
Brand: Talkswitch Pages: 9
OSS OSS-KIT-EXP-6002 User Manual preview
OSS-KIT-EXP-6002
Brand: OSS Pages: 15
Atmel ATAK5276-83 Application Note preview
ATAK5276-83
Brand: Atmel Pages: 17

Brands by name

Popular brands

Load more brands