manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

Share
Download
Freescale Semiconductor MPC5632M Manual Download Page 804

MPC563XM Reference Manual, Rev. 1

804

Freescale Semiconductor

 

Preliminary—Subject to Change Without Notice

Table 23-21

 summarizes Event Registers accesses.

Match1 and Match2 Registers

Match1 and Match2 registers hold a match value to be compared against the selected channel time base. 
A match value can only be written into the Match register by microcode, through ERT1/2 microengine 
registers (see 

Section 23.4.9.3.5, “Write Channel Match and UDCM Registers

”). Microcode can also read 

the Match register as a special T4ABS source operation, when T4ABS=0101, and the source for T4ABS 
is selected from the second register set. In this operation, Match1/2 registers are copied into ERT1/2 
registers (see 

Section 23.4.9.2.2, “Selecting Sources and Destination

”). For more information on time base 

matches, see 

Section 23.4.5.2, “Match Recognition

.”

Capture1 and Capture2 Registers

Capture1 and Capture2 registers capture the selected channel time base. Capture1/2 registers cannot be 
directly written or read by microcode. During the Time Slot Transition (TST) or during CHAN assignment, 
Capture1/2 registers are copied into ERT1/2 microengine registers. For more information, see 

Section 23.4.5.3, “Transition Detection and Time Base Capture

”.

TBS1 and TBS2 - Time Base Selection Registers

TBS1/2 are 3-bit registers which have the following effect on channel configuration:

•

Selection of the timebase (TCR1 or TCR2) to be compared against the match values in Match1 
and/or Match2 registers.

Table 23-21. Event Registers microcode accesses

 

Register

Access Type

Sampled from 

channel

Update to

channel

Microcode

fields

1

1

see 

Section 23.4.9, “Microinstruction Set

.”

Reset

value

2

2

n.a. means that value of the register is undetermined after reset.

Capture1, Capture2

read through ERT1/2

to ERT1/2 on 

CHAN assignment

no

T2ABD

n.a.

Match1, Match2

read and write through ERT1/2

to ERT1/2 

by microcode

from ERT1/2 

by microcode

ERW1, 

CMW, 

ERW2, 
T4ABS

n.a.

MRLE1, MRLE2

write to 0 (negate) directly;

write to 1 (assert) upon 

Match1/2 update from ERT1/2

no

immediate

MRLE, 

ERW1, 

ERW2

0, 0

TBS1, TBS2

write only

no

immediate

TBS1, TBS2

000, 

000

MRL1, MRL2

flag test on branch, 

write to 0 (negate) only

on CHAN 

assignment

immediate

BCC (test)

MRL1, 

MRL2 

(reset)

0, 0

TDL1, TDL2

flag test on branch,

write to 0 (negate) only

on CHAN 

assignment

immediate

BCC (test)

TDL (reset)

0, 0

TCCE1

write only

no

immediate

MTD

0

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands