Freescale Semiconductor MPC5632M Manual Download Page 387

Page: 387 / 1384

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

387

Preliminary—Subject to Change Without Notice

Figure 13-49. External Master 32-bit Read from MCU with DBM=1

CLKOUT

ADDR[8:31]

TS (input)

RD_WR

TSIZ[0:1]

*DATA[0:15]

TA (output)

DATA is valid

Minimum 2 Wait States

BR (input)

receive bus grant and bus busy negated for 2nd cycle

assert BB, drive address and assert TS

Using the Internal arbiter

BDIP

DATA is valid

‘00’

* Or DATA[16:31], based on D16_31 bit in EBI_MCR.

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MPC5632M

Reviews:

Related manuals for MPC5632M

Brands by name

Popular brands

Freescale Semiconductor MPC5632M, Manual

Search results

Summary of Contents for MPC5632M

Reviews:

Related manuals for MPC5632M

Brands by name

Popular brands