manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

Share
Download
Freescale Semiconductor MPC5632M Manual Download Page 169

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

169

 

Preliminary—Subject to Change Without Notice

Chapter 8  
Multi-Layer AHB Crossbar Switch (XBAR)

8.1

Information Specific to This Device

This section presents device-specific parameterization and customization information not specifically 
referenced in the remainder of this chapter.

8.1.1

Device-Specific Block Diagram

Figure 8-1

 shows the simplified block diagram specific to this device.

Figure 8-1. Device-Specific Block Diagram

8.1.2

Device-Specific Features

•

Three master ports

— e200z335 core complex Instruction port

— e200z335 core complex Load/Store port

— eDMA

•

Four slave ports:

— Flash memory

— SRAM

— Peripheral bridge B (eTPU, SIU, DSPI, eSCI, FlexCAN, eQADC, BAM)

— Calibration bus

•

32-bit internal address, 64-bit internal data paths (64 bit for instruction fetch)

•

AXBS halt mode is not supported on this device. The functionality associated with 
axbs_halt_request is not implemented as this signal is tied off inside the platform. Also, dynamic 
priority elevation and alternate context switching are not supported on this device.

•

Table 8-1

 shows the master-slave connections for this device.

Peripheral Bridge

Flash memory

SRAM

Calibration Bus

e200z335 core Instruction

eDMA

e200z335 core Load/Store

Unused master port

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands