manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

Share
Download
Freescale Semiconductor MPC5632M Manual Download Page 1279

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

1279

 

Preliminary—Subject to Change Without Notice

28.4.4.1

Module Configuration Register (MCR)

This register defines global system configurations, such as the module operation mode (e.g., low power) 
and maximum message buffer configuration. Most of the fields in this register can be accessed at any time, 
except the MAXMB field, which should only be changed while the module is in Freeze Mode.

Figure 28-5. Module Configuration Register (MCR)

MDIS — Module Disable

This bit controls whether FlexCAN is enabled or not. When disabled, FlexCAN shuts down the clocks 
to the CAN Protocol Interface and Message Buffer Management sub-modules. This is the only bit in 
MCR not affected by soft reset. See 

Section 28.5.9.2, “Module Disable Mode,”

 for more information.

1 = Disable the FlexCAN module
0 = Enable the FlexCAN module

FRZ — Freeze Enable

The FRZ bit specifies the FlexCAN behavior when the HALT bit in the MCR Register is set or when 
Debug Mode is requested at MCU level. When FRZ is asserted, FlexCAN is enabled to enter Freeze 
Mode. Negation of this bit field causes FlexCAN to exit from Freeze Mode.

1 = Enabled to enter Freeze Mode
0 = Not enabled to enter Freeze Mode

FEN — FIFO Enable

This bit controls whether the FIFO feature is enabled or not. When FEN is set, MBs 0 to 7 cannot be 
used for normal reception and transmission because the corresponding memory region ($80-$FF) is 
used by the FIFO engine. See 

Section 28.4.3, “Rx FIFO Structure

 

and

 

Section 28.5.7, “Rx FIFO,”

 for 

more information.

Base + $0000

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

MDIS

FRZ

FEN

HALT

NOT_

RDY

WAK_

MSK

SOFT

_RST

FRZ_

ACK SUPV

SLF_

WAK

WRN

_EN

LPM_

ACK

WAK_

SRC

DOZE

SRX

_DIS

BCC

W

RESET:

Note

1

1

Reset value of this bit is different on various platforms. Consult the specific MCU documentation to determine 
its value.

1

0

1

1

0

0

Note

2

2

Different on various platforms, but it is always the opposite of the MDIS reset value.

1

0

0

Note

3

3

Different on various platforms, but it is always the same as the MDIS reset value.

0

0

0

0

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

0

0

LPRI

O_EN

AEN

0

0

IDAM

0

0

MAXMB

W

RESET:

0

0

0

0

0

0

0

0

0

0

0

0

1

1

1

1

= Unimplemented or Reserved

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands