Freescale Semiconductor MPC5632M, Manual

Share

Page: 1226 / 1384

Freescale Semiconductor MPC5632M Manual Download Page 1226

MPC563XM Reference Manual, Rev. 1

1226

Freescale Semiconductor

Preliminary—Subject to Change Without Notice

27.3.2.10 SCI Status Register 2 (SCISR2)

This register provides the BERR flag to indicate the occurrence of a module event and status bits to
indicate the state of the module. The BERR flag can be used to generate an interrupt request. The related
interrupt enable bit is located in

SCI Control Register 3 (SCICR3)

3

OR

Overrun Flag. This flag is set when an overrun was detected as described in

Section 27.4.5.3.11, “Receiver

Note:

This flag is set in SCI mode only.

2

NF

Noise Flag. This flag is set when the payload data of a received frame was transferred into the

SCI Data Register

and

SCI Data Register Low (SCIDRL)

or

LIN RX Register (LINRX)

and the receiver has detected

noise during the reception of that frame, as described in

Section 27.4.5.3.13, “Bit Sampling

1

FE

Framing Error Flag. This flag is set when the payload data of a received frame was transferred into the

Register High (SCIDRH)

SCI Data Register Low (SCIDRL)

LIN RX Register (LINRX)

and the receiver has

detected a framing error during the reception of that frame, as described in

Section 27.4.5.3.18, “Stop Bit

”.

0

PF

Parity Error Flag. This flag is set when the payload data of a received frame was transferred into the

Register High (SCIDRH)

SCI Data Register Low (SCIDRL)

and the receiver has detected a parity error for

the character, as described in

Section 27.4.5.4, “Reception Error Reporting

Note:

This flag is set in SCI mode only.

Address Offset: 0x09

Access: User read/write (write to clear)

7

6

5

4

3

2

1

0

R

0

0

0

BERR

0

0

TACT

RACT

W

w1c

Reset

0

0

0

0

0

0

0

0

Figure 27-11. SCI Status Register 2 (SCISR2)

Table 27-15. SCISR2 Field Descriptions

Field

Description

4

BERR

Bit Error Flag. This flag is set when a bit error was detected as described in

Section 27.4.6.5.3, “Standard Bit

Error Detection

Note:

This flag is set in LIN mode only.

1

TACT

Transmitter Active. The status bit is set as long as the transmission of a frame or special character is ongoing.
0 No transmission in progress.
1 Transmission in progress.

0

RACT

Receiver Active. The bit will be set 3 receiver clock (RCLK) cycles after the successful qualification of a start bit.
This bit will be cleared, when an idle character was detected.
0 No reception in progress.
1 Reception in progress.

Table 27-14. SCISR1 Field Descriptions (continued)

Field

Description

«
...
1224
1225
1226
1227
1228
...
»

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands