manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

The Freescale Semiconductor MPC5632M is a cutting-edge microcontroller designed for a wide range of applications. With its advanced features and high performance, this product is perfect for professionals and enthusiasts alike. Discover its full potential by downloading the user manual for free from our website.

Share
Download
background image

MPC563XM Reference Manual, Rev. 1

1120

Freescale Semiconductor

 

Preliminary—Subject to Change Without Notice

The FRZ bit control the freeze mode of the Decimation Filter. In order to be effective the FREN freeze 
enable bit needs also to be asserted. While in freeze mode the MAC operations are halted. Refer to 

Section 25.5.12, “Freeze Mode Description,”

 for more details.

1 = Decimation Filter in Freeze Mode
0 = Decimation Filter in Normal Mode

SRES — Software-reset bit

The SRES is a self-negated bit which provides for the CPU the capability to initialize the Decimation 
Filter through the Sky-blue interface. This bit reads always as zero. Refer to 

Section 25.5.10, 

“Soft-Reset Command Description,”

 for more details.

1 = Software-Reset 
0 = No action

IDEN — Input Data Interrupt Enable

The IDEN bit enables the Decimation Filter to generate interrupt requests on every new input data 
written to the Interface Input Buffer register or Input/Output Buffers register.

1 = Input Data Interrupt Enabled
0 = Input Data Interrupt Disabled

ODEN — Output Data Interrupt Enable

The ODEN bit enables the Decimation Filter to generate interrupt requests on every new data written 
to the filter Output buffer. It is independent of ISEL setting.

1 = Output Data Interrupt Enabled
0 = Output Data Interrupt Disabled

ERREN — Error Interrupt Enable

The ERREN bit enables the Decimation Filter to generate interrupt requests based on the assertion of 
the Error Flags OVF, OVR or IVR.

1 = Error Interrupts Enabled
0 = Error Interrupts Disabled

FTYPE[1:0] — Filter Type Selection bits

The FTYPE[1:0] bits select the filter type according to 

Table 25-2

.

SCAL[1:0] — Filter Scaling Factor

The SCAL[1:0] bit field selects the scaling factor used by the filter algorithm according to 

Table 25-3

.

Table 25-2. FTYPE[1:0] - Filter Type Selection

FTYPE[1:0]

Description

00

Filter Bypass

1

1

In Bypass configuration the filter is disabled.

01

IIR Filter

10

FIR Filter

11

Reserved

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5632M

Daikin Maverick I Operation Manual preview
Maverick I
Brand: Daikin Pages: 48
Daikin MicroTech III Operating Manual preview
MicroTech III
Brand: Daikin Pages: 77
Daikin MicroTech III Operation And Maintenance Manual preview
MicroTech III
Brand: Daikin Pages: 32
Daikin MicroTech III Installation And Maintenance Manual preview
MicroTech III
Brand: Daikin Pages: 14
Daikin DCS601C51 Hardware Manual preview
DCS601C51
Brand: Daikin Pages: 16
Daikin BRC944B2 Quick User Manual preview
BRC944B2
Brand: Daikin Pages: 1
Lattice Semiconductor HDR-60 User Manual preview
HDR-60
Brand: Lattice Semiconductor Pages: 26
Gamma Vacuum SPCe User Manual preview
SPCe
Brand: Gamma Vacuum Pages: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Brand: Gamma Pages: 28
Lab.gruppen LAB.LEVEL4 Quick Start Manual preview
LAB.LEVEL4
Brand: Lab.gruppen Pages: 2
I-Tork PDS Series Installation & Operation Manual preview
PDS Series
Brand: I-Tork Pages: 15
Desoutter 6159326760 Original Instructions Manual preview
6159326760
Brand: Desoutter Pages: 74
Danfoss VLT MCD 201 Installation Manual preview
VLT MCD 201
Brand: Danfoss Pages: 36
ATT Holding Kade KZ-700-U/H Installation Manual preview
Kade KZ-700-U/H
Brand: ATT Holding Pages: 12
Genasun GVB-8-WP Series Manual preview
GVB-8-WP Series
Brand: Genasun Pages: 8
Gardenic GN-1113 User Manual preview
GN-1113
Brand: Gardenic Pages: 14
M-Audio Keystation 61es User Manual preview
Keystation 61es
Brand: M-Audio Pages: 15
fadini Elpro S40 Manual preview
Elpro S40
Brand: fadini Pages: 40

Brands by name

Popular brands

Load more brands