manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 816

UART Modules

Freescale Semiconductor

32-22

•

In block mode, the USR

n

 shows a logical OR of all characters reaching the top of the FIFO since 

the last RESET ERROR STATUS command. Status is updated as characters reach the top of the 
FIFO. Block mode offers a data-reception speed advantage where the software overhead of 
error-checking each character cannot be tolerated. However, errors are not detected until the check 
is performed at the end of an entire message—the faulting character is not identified.

In either mode, reading the USR

n

 does not affect the FIFO. The FIFO is popped only when the receive 

buffer is read. The USR

n

 should be read before reading the receive buffer. If all three receiver holding 

registers are full, a new character is held in the receiver shift register until space is available. However, if 
a second new character is received, the contents of the character in the receiver shift register is lost, the 
FIFOs are unaffected, and USR

n

[OE] is set when the receiver detects the start bit of the new overrunning 

character.

To support flow control, the receiver can be programmed to automatically negate and assert U

n

RTS, in 

which case the receiver automatically negates U

n

RTS when a valid start bit is detected and the FIFO is 

full. The receiver asserts U

n

RTS when a FIFO position becomes available; therefore, connecting U

n

RTS 

to the U

n

CTS input of the transmitting device can prevent overrun errors.

NOTE

The receiver continues reading characters in the FIFO if the receiver is 
disabled. If the receiver is reset, the FIFO, U

n

RTS control, all receiver status 

bits, interrupts, and DMA requests are reset. No more characters are 
received until the receiver is reenabled.

32.4.3

Looping Modes

The UART can be configured to operate in various looping modes. These modes are useful for local and 
remote system diagnostic functions. The modes are described in the following paragraphs and in 

Section 32.3, “Memory Map/Register Definition.”

The UART’s transmitter and receiver should be disabled when switching between modes. The selected 
mode is activated immediately upon mode selection, regardless of whether a character is being received 
or transmitted.

32.4.3.1

Automatic Echo Mode

In automatic echo mode, shown in 

Figure 32-21

, the UART automatically resends received data bit by bit. 

The local CPU-to-receiver communication continues normally, but the CPU-to-transmitter link is 
disabled. In this mode, received data is clocked on the receiver clock and re-sent on U

n

TXD. The receiver 

must be enabled, but the transmitter need not be.

Figure 32-21. Automatic Echo

Disabled

Disabled

Tx

Rx

CPU

U

n

RXD Input

U

n

RXD Input

U

n

TXD Output

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands