manualshive.com logo in svg

Freescale Semiconductor MCF5329, Reference Manual, Page: 290 / 924

Share
Download
Freescale Semiconductor MCF5329 Reference Manual Download Page 290

Edge Port Module (EPORT)

15-2

Freescale Semiconductor

15.2

Low-Power Mode Operation

This section describes the operation of the EPORT module in low-power modes. For more information on 
low-power modes, see 

Chapter 8, “Power Management”.

 

Table 15-1

 shows EPORT-module operation in 

low-power modes and describes how this module may exit each mode.

NOTE

The wakeup control register (WCR) in the system control module specifies 
the interrupt level at or above what is needed to bring the device out of a 
low-power mode.

In wait and doze modes, the EPORT module continues to operate as it does in run mode. It may be 
configured to exit the low-power modes by generating an interrupt request on a selected edge or a low level 
on an external pin. In stop mode, no clocks are available to perform the edge-detect function. Only the 
level-detect logic is active (if configured) to allow any low level on the external interrupt pin to generate 
an interrupt (if enabled) to exit stop mode. 

NOTE

In stop mode, the input pin synchronizer is bypassed for the level-detect 
logic because no clocks are available.

15.3

Interrupt/GPIO Pin Descriptions

All EPORT pins default to general-purpose input pins at reset. The pin value is synchronized to the rising 
edge of FB_CLK when read from the EPORT pin data register (EPPDR). The values used in the edge/level 
detect logic are also synchronized to the rising edge of FB_CLK. These pins use Schmitt-triggered input 
buffers with built-in hysteresis designed to decrease the probability of generating false, edge-triggered 
interrupts for slow rising and falling input signals.

When a pin is configured as an output, it is driven to a state whose level is determined by the corresponding 
bit in the EPORT data register (EPDR). All bits in the EPDR are set at reset.

15.4

Memory Map/Register Definition

This subsection describes the memory map and register structure. Refer to 

Table 15-2

 for a description of 

the EPORT memory map.

Table 15-1. Edge Port Module Operation in Low-Power Modes

Low-power Mode

EPORT Operation

Mode Exit

Wait

Normal

Any IRQn interrupt at or above level in WCR

Doze

Normal

Any IRQn interrupt at or above level in WCR

Stop

Level-sensing only

Any IRQn interrupt set for level-sensing at or 
above level in WCR. See note below.

MCF5329 Reference Manual, Rev 3

Summary of Contents for MCF5329





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments