Freescale Semiconductor MCF52277 Reference Manual Download Page 634 | Manualshive

Page: 634 / 800

background image

Programmable Interrupt Timers (PIT0–PIT1)

MCF52277 Reference Manual, Rev. 1

27-2

Freescale Semiconductor

NOTE

The low-power interrupt control register (LPICR) in the system control
module specifies the interrupt level at or above which the device can be
brought out of a low-power mode.

In wait mode, the PIT module continues to operate as in run mode and can be configured to exit the
low-power mode by generating an interrupt request. In doze mode with the PCSR

n

[DOZE] bit set, PIT

module operation stops. In doze mode with the PCSR

n

[DOZE] bit cleared, doze mode does not affect PIT

operation. When doze mode is exited, PIT continues operating in the state it was in prior to doze mode. In
stop mode, the internal bus clock is absent and PIT module operation stops.

In debug mode with the PCSR

n

[DBG] bit set, PIT module operation stops. In debug mode with the

PCSR

n

[DBG] bit cleared, debug mode does not affect PIT operation. When debug mode is exited, the PIT

continues to operate in its pre-debug mode state, but any updates made in debug mode remain.

27.2

Memory Map/Register Definition

This section contains a memory map (see

) and describes the register structure for PIT0–PIT1.

NOTE

Longword accesses to any of the programmable interrupt timer registers
results in a bus error. Only byte and word accesses are allowed.

Table 27-1. PIT Module Operation in Low-power Modes

Low-power Mode

PIT Operation

Mode Exit

Wait

Normal

N/A

Doze

Normal if PCSR

n

[DOZE] cleared,

stopped otherwise

Any interrupt at or above level in LPICR, exit doze

mode if PCSR

n

[DOZE] is set. Otherwise

interrupt assertion has no effect.

Stop

Stopped

No

Debug

Normal if PCSR

n

[DBG] cleared,

stopped otherwise

No. Any interrupt is serviced upon normal exit

from debug mode

Table 27-2. Programmable Interrupt Timer Modules Memory Map

Address

Register

Width

(bits)

Access

1

Reset Value

Section/Page

PIT 0
PIT 1

Supervisor Access Only Registers

2

0xFC08_0000
0xFC08_4000

PIT Control and Status Register (PCSR

n

)

16

R/W

0x0000

0xFC08_0002
0xFC08_4002

PIT Modulus Register (PMR

n

)

16

R/W

0xFFFF

«
...
632
633
634
635
636
...
»

Summary of Contents for MCF52277

































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MCF52277

Univerge SV9300

Brand: NEC Pages: 26

Brand: NEC Pages: 20

DS2000 IntraMail

Brand: NEC Pages: 2

Brand: Paradyne Pages: 12

NI WLS/ENET-9163

Brand: National Instruments Pages: 36

Brand: Qlogic Pages: 8

Brand: ZALMAN Pages: 5

RouterBOARD 411R

Brand: 4gon Pages: 2

TD-3316B4-16P-A1

Brand: TVT Digital Pages: 2

Brand: Cisco MERAKI Pages: 4

Brand: Juniper Pages: 420

Brand: Accusys Pages: 34

Brand: Kontron Pages: 62

CORE 2 DUO E4000 - 3-2008

Brand: Intel Pages: 122

Brand: HMS Pages: 18

MS-96 Vial Reader

Brand: Microscan Pages: 67

Brand: Renesas Pages: 67

Brand: Avigilon Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands