manualshive.com logo in svg

Freescale Semiconductor MC9S12ZVHL32, Reference Manual

The Freescale Semiconductor MC9S12ZVHL32 is a powerful microcontroller designed for automotive applications. For a comprehensive understanding of its features and functionalities, make sure to download the free Reference Manual from manualshive.com. This manual provides detailed instructions for maximizing the performance of this cutting-edge product.

Share
Download
background image

Chapter 9 Pulse-Width Modulator (S12PWM8B8CV2) 

S12ZVHY/S12ZVHL Family Reference Manual Rev. 1.05

324

Freescale Semiconductor

In freeze mode there is a software programmable option to disable the input clock to the prescaler. This is 
useful for emulation.

Wait:

The prescaler keeps on running, unless PSWAI in PWMCTL is set to 1. 

Freeze:

The prescaler keeps on running, unless PFRZ in PWMCTL is set to 1. 

9.1.3

Block Diagram

Figure 9-1

 shows the block diagram for the 8-bit up to 8-channel scalable PWM block.

Figure 9-1. Scalable PWM Block Diagram

9.2

External Signal Description

The scalable PWM module has a selected number of external pins. Refer to device specification for exact 
number.

Period and Duty 

Counter 

Channel 6

Clock Select 

PWM Clock 

Period and Duty 

Counter 

Channel 5

Period and Duty 

Counter 

Channel 4

Period and Duty 

Counter 

Channel 3

Period and Duty 

Counter 

Channel 2

Period and Duty 

Counter 

Channel 1

Alignment

Polarity

Control

PWM8B8C

PWM6

PWM5

PWM4

PWM3

PWM2

PWM1

Enable

PWM Channels

Period and Duty 

Counter 

Channel 7

Period and Duty 

Counter 

Channel 0

PWM0

PWM7

Bus Clock

Maximum possible channels, scalable in pairs from PWM0 to PWM7.

Summary of Contents for MC9S12ZVHL32











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MC9S12ZVHL32

CAME Z Series Technical Documentation Manual preview
Z Series
Brand: CAME Pages: 16
Ultrak KEGS5000 User Manual preview
KEGS5000
Brand: Ultrak Pages: 41
Zander Aachen ZX Series Quick Start Manual preview
ZX Series
Brand: Zander Aachen Pages: 10
QED MP50 Instruction Manual preview
MP50
Brand: QED Pages: 26
Radware Alteon Installation And Maintenance Manual preview
Alteon
Brand: Radware Pages: 98
ZKTeco SRB Connection Manual preview
SRB
Brand: ZKTeco Pages: 2
S&C IntelliCap Installation Manual preview
IntelliCap
Brand: S&C Pages: 24
ZiLOG Z8 Encore! XP Dual F1680 Series User Manual preview
Z8 Encore! XP Dual F1680 Series
Brand: ZiLOG Pages: 18
Danfoss AME 56K Instructions Manual preview
AME 56K
Brand: Danfoss Pages: 10
SSHC TSSHC-3IL-24 Quick Start Manual preview
TSSHC-3IL-24
Brand: SSHC Pages: 2
SIATA PS0335 XP0/05 Service Manual preview
PS0335 XP0/05
Brand: SIATA Pages: 7
Fairchild HPD1***A**K*N Installation, Operation And Maintenance preview
HPD1***A**K*N
Brand: Fairchild Pages: 4
S+S Regeltechnik HYGRASREG KH-10 Operating Instructions, Mounting & Installation preview
HYGRASREG KH-10
Brand: S+S Regeltechnik Pages: 16
EuroLite DMX LED EASY Operator Deluxe User Manual preview
DMX LED EASY Operator Deluxe
Brand: EuroLite Pages: 16
iceqube MINI MAX Programming Manual preview
MINI MAX
Brand: iceqube Pages: 2
Lintec MC-3000L-TC Series Instruction Manual preview
MC-3000L-TC Series
Brand: Lintec Pages: 2
Xylem CentriPro SPD Plus Instruction Manual preview
CentriPro SPD Plus
Brand: Xylem Pages: 36
Logosol 9122310174 Manual preview
9122310174
Brand: Logosol Pages: 60

Brands by name

Popular brands

Load more brands