manualshive.com logo in svg

Freescale Semiconductor e200z3, Reference Manual

The Freescale Semiconductor e200z3 is a powerful product designed for seamless performance. With our comprehensive Reference Manual, users can easily navigate through the device's features and functionalities. Download this manual for free from manualshive.com, enabling you to understand and maximize the potential of this remarkable product.

Share
Download
background image

Nexus3/ Module

e200z3 Power Architecture Core Reference Manual, Rev. 2

Freescale Semiconductor

10-31

 

The formats for program trace direct/indirect branch with synchronized messages and indirect branch 
history with synchronized messages are shown in 

Figure 10-26

:

Exception conditions that result in program trace synchronization are summarized in 

Table 10-24

.

(1–32 bits)

(1–32 bits)

(1–8 bits)

(4 bits)

(6 bits)

Branch History

Full Target Address

Sequence 

Count

Source 

Process

TCODE 

(011101)

Maximum length = 82 bit; Minimum length = 13 bits

Figure 10-26. Indirect Branch History with Synchronization Message Format

Table 10-24. Program Trace Exception Summary

Exception Condition

Exception Handling

System reset 
negation

At the negation of JTAG reset, 

j_trst_b, queue pointers, counters, state machines, and registers within 

the Nexus3/ module are reset. Upon the first branch out of system reset, if program trace is 
enabled, the first program trace message is a direct/indirect branch with synchronization message.

Program trace 
enabled

The first program trace message, after program trace has been enabled, is a synchronization message.

Exit from low 
power/debug

Upon exit from a low-power mode or debug mode, the next direct/indirect branch is converted to a 
direct/indirect branch with synchronization message.

Queue overrun

An error message occurs when the message queue is full and a new message cannot be queued. The 
FIFO discards messages until it has completely emptied the queue. Once emptied, an error message 
is queued. The error encoding indicates which types of messages attempted to be queued while the 
FIFO was being emptied. The next BTM message in the queue is a direct/indirect branch with 
synchronization message.

Periodic program 
trace synchronization

A forced synchronization occurs periodically after 255 program trace messages have been queued. A 
direct/indirect branch with synchronization message is queued. The periodic program trace message 
counter then resets.

Event in

If the Nexus module is enabled, assorting 

nex_evti_b initiates a direct/indirect branch with 

synchronization message upon the next direct/indirect branch, if program trace is enabled and the EIC 
bits of the DC1 register have enabled this feature.

Sequential instruction 
count overflow

When the sequential instruction counter reaches its maximum count (up to 255 sequential instructions 
may be executed), a forced synchronization occurs. The sequential counter then resets. A program 
trace direct/indirect branch with synchronization message is queued upon execution of the next branch.

Attempted access to 
secure memory

For SOCs that implement security, any attempted branch to secure memory locations temporarily 
disables program trace and causes the corresponding BTM to be lost. The following direct/indirect 
branch queues a direct/indirect branch with synchronization message. The count value within this 
message will be inaccurate since the re-enable of program trace is not necessarily aligned on an 
instruction boundary.

Collision priority

All messages have the following priority: WPM 

→

 OTM 

→

 BTM 

→

 DTM. A BTM message that attempts 

to enter the queue at the same time as a watchpoint message or ownership trace message is lost. An 
error message is sent indicating the BTM was lost. The following direct/indirect branch queues a 
direct/indirect branch with synchronization message. The count value within this message reflects the 
number of sequential instructions executed after the last successful BTM message was generated. This 
count includes the branch that did not generate a message due to the collision.

Execution mode 
switch

Whenever the CPU switches execution mode into or out of a sequence of VLE instructions, the next 
branch trace message will be a Direct/Indirect Branch w/ Sync Message.

Summary of Contents for e200z3



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for e200z3

Hal Communications RS2100 Instruction Manual preview
RS2100
Brand: Hal Communications Pages: 25
Industrex M43ic Instruction Manual preview
M43ic
Brand: Industrex Pages: 51
Black Box JPM083A Manual preview
JPM083A
Brand: Black Box Pages: 9
FS FS-BOX-V3 Quick Start Manual preview
FS-BOX-V3
Brand: FS Pages: 19
Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
IBASE Technology IB952 Series User Manual preview
IB952 Series
Brand: IBASE Technology Pages: 71
Net to Net Technologies UIM-1000T Installation Instructions preview
UIM-1000T
Brand: Net to Net Technologies Pages: 4
Zoom 4412A User Manual preview
4412A
Brand: Zoom Pages: 48
Ericsson Marconi OMS 1200 Product Description preview
Marconi OMS 1200
Brand: Ericsson Pages: 136
Hama 00039747 Operating Instruction preview
00039747
Brand: Hama Pages: 6
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Brand: ADC Pages: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Brand: Renesas Pages: 28
EMTRUST CP75X User Manual preview
CP75X
Brand: EMTRUST Pages: 103
Network Critical SmartNA-X User Manual preview
SmartNA-X
Brand: Network Critical Pages: 200
ENERMAX LIQMAX III ELC-LMT120-ARGB User Manual preview
LIQMAX III ELC-LMT120-ARGB
Brand: ENERMAX Pages: 32
Omron NJ501-1300 User Manual preview
NJ501-1300
Brand: Omron Pages: 432
Idis DR-2308P Quick Manual preview
DR-2308P
Brand: Idis Pages: 18

Brands by name

Popular brands

Load more brands