manualshive.com logo in svg

Freescale Semiconductor ColdFire MCF5211, Reference Manual

Share
Download
Freescale Semiconductor ColdFire MCF5211 Reference Manual Download Page 357

UART Modules

MCF5213 ColdFire® Integrated Microcontroller Reference Manual, Rev. 3

Freescale Semiconductor

21-27

 

To configure the UART for DMA requests:

1. Initialize the DMAREQC in the SCM to map the desired UART DMA requests to the desired DMA 

channels. For example; setting DMAREQC[7:4] to 1000 maps UART0 receive DMA requests to 
DMA channel 1; setting DMAREQC[11:8] to 1101 maps UART1 transmit DMA requests to DMA 
channel 2; and so on. It is possible to independently map transmit based and receive based UART 
DMA requests in the DMAREQC. 

2. Disable interrupts using the UIMR register. The appropriate UIMR bits must be cleared so that 

interrupt requests are disabled for those conditions for which a DMA request is desired. For 
example; to generate transmit DMA requests from UART1, then UIMR1[TXRDY] should be 
cleared. This will prevent TXRDY from generating an interrupt request while a transmit DMA 
request is generated.

3. Configure the GPACR and appropriate PACR registers located in the SCM for DMA access to 

IPSBAR space.

4. Initialize the DMA channel. The DMA should be configured for cycle steal mode and a source and 

destination size of one byte. This will cause a single byte to be transferred for each UART DMA 
request.

Table 21-14

 shows the DMA requests.

21.5.2

UART Module Initialization Sequence

Table 21-15

 shows the UART module initialization sequence.

Table 21-14. UART DMA Requests

Register

Bit

DMA Request

UISR

n

1

Receive DMA request

UISR

n

0

Transmit DMA request

Table 21-15. UART Module Initialization Sequence

Register

Setting

UCR

n

Reset the receiver and transmitter.
Reset the mode pointer (MISC[2–0] equals 0b001).

UIMR

n

Enable the desired interrupt sources.

UACR

n

Initialize the input enable control (IEC bit).

UCSR

n

Select the receiver and transmitter clock. Use timer as source if required.

UMR1

n

If preferred, program operation of receiver ready-to-send (RXRTS bit).
Select receiver-ready or FIFO-full notification (RXRDY/FFULL bit).
Select character or block error mode (ERR bit).
Select parity mode and type (PM and PT bits).
Select number of bits per character (B/Cx bits).

Summary of Contents for ColdFire MCF5211

































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands