Recalling Presets
128 presets provided by the MOTION LOOP can be recalled in
various ways.
Use PRESET Footswitch to Switch between
Presets 1 and 2
Press the PRESET footswitch to switch the presets.
Recall Desired Preset from 128 Presets
1.
Press the
HOME
switch until the screen shows a preset number
and preset name.
2.
Turn the
PARAMETER
encoder until the desired preset number is
shown in the display. The two red LEDs above the
PRESET
footswitch flash alternately. At this time the preset is not recalled.
3.
Press the
PRESET
footswitch to recall the desired preset. When
the preset is recalled, the two red LEDs above the footswitch stop
alternate flashing.
Recall Preset by MIDI Signal
The MOTION LOOP’s presets are switched by receiving a program
change number MIDI signal from an external MIDI device. The MIDI
channel of the device that sends the program change number has to
be the same as the MIDI channel of the MOTION LOOP.
Factory Presets
The MOTION LOOP is shipped with factory presets. They are stored
in the user preset memory after No. 128 with the [F:] preset number
prefix. Users can turn the
PARAMETER
encoder to select and recall
the desired factory preset.
Note that this factory preset area is protected against recall, write,
or delete operation via MIDI signals.
Note that the parameters of the factory presets have already been
copied into the user preset area to be used after being edited to the
user’s preference.
For more details about the factory presets, please refer to the
product page on our website.
1.
Press the
HOME
switch to show the HOME or Assignment Display
screen.
2.
Press the
▶
cursor key to show the HOME screen.
3.
Turn the
PARAMETER
encoder to show the desired setting menu.
4.
Press the
◀
/
▶
cursor key to select the desired setting.
5.
Turn the
PARAMETER
encoder to change the parameter.
1.
Press the
SAVE
switch. The
SAVE
LED and preset number display
start flashing.
2.
Turn the
PARAMETER
encoder to change the preset number
shown in the display to the desired preset number. (Skip this step if
overwriting in the same preset number.)
3.
Press the
SAVE
switch. The edited parameter is stored in the preset.
How to Change Parameters and Saving Them
in Preset
How to Confirm Parameter Changes or Settings
The effects unit’s parameters in each preset and the function of
each knob,
PARAMETER
encoder, or footswitch, etc. are changed in
Edit mode.
Edit Menu
Setting Procedures for Global Functions
In the Global Settings screen, settings related to the entire operation
such as MIDI receive channel selection, calibration of expression
pedal, etc. are configured.
1.Hold down the HOME switch for about 2 seconds to show the
Global Settings screen.
2.Use the
◀
/
▶
cursor key to show the desired setting screen.
3.Configure the desired function.
4.Press the HOME switch. The display changes to the HOME screen.
Global Settings
PRESET NAME
HOME SCREEN
①
Setting of MIDI
Receive Channel
(MIDI CH)
②
Calibration of
Expression Pedal
(EXP CALB)
③
Display of
Expression Pedal
(EXP DISP)
④
Setting for
【
PARAMETER
】
Encorder
(ENCODER)
⑤
Setting for
【
PRESET
】
Switch
(PS FSW)
6.
When confirmation or editing is completed, press the
HOME
switch. The display shows the HOME screen again.
NOTE
To cancel the save operation, press the HOME switch (i.e., other than
the SAVE switch) or
◀
/
▶
cursor key when the number shown in the
display is flashing. Or move the LOOP RATE, E.LEVEL, or FILTER knob
to cancel the save operation. If a parameter of a saved preset has
been changed, a dot appears at the lower right corner of the first
digit of the PRESET number. This dot is turned off when the changed
parameter is saved in the preset.
The following steps clears all presets and returns them to the
factory status.
1.
Hold the
▶
cursor key down and turn on the power to the unit.
2.
Release
▶
cursor key when the display shows “
INITIALIZING.
”
3.
This completes the initialization.
Initialization
NOTE
Each time the PRESET footswitch is pressed, Presets 1 and 2 are
switched instantly. It is useful to store frequently used presets in
Preset 1 and Preset 2 and switch them.
HOME SCREEN
FUNCTION
ASSIGNMENT
SCREEN
①
PITCH SETTING
②
LOOP SETTING
③
WAVEFORM SETTING
④
DELAY SETTING
⑤
DRY & FOOTSW SETTING
⑥
KNOB & EXP ASSIGN
⑦
PRESET NAME
OCTAVE UP/DOWN
1, 2OCT UP
1, 2 OCT DOWN
PITCH VALUE
000
〜
100
PITCH SPEED
000
〜
100
PITCH SHIFT
REPEAT, SINGLE
SLOW DOWN
ON, OFF
LOOP LEVEL
-100
〜
100
RETRIGGER SETTING
OFF, FOOTSW, ATTACK
RESET LEVEL
RETRIGG, NONE
RETRIGGER SENS
O
〜
100
FADE CURVE
SHALLOW, DEEP, A CURVE,
C CURVE, REVERSE
FILTER MODE
MANUAL, ENV,
SYNC BPM, SYNC SPD
FILTER RANGE
NARROW, WIDE
SOFT CLIPPING
000
〜
100
DELAY SUBDIVISION
OFF, 1, 1/2, 1/4, .1/8, 1/8
DELAY MIX LEVEL
000
〜
100
DELAY FEEDBACK
000
〜
100
DRY SETUP
ON, AUTO, OFF
ON/OFF FOOTSW
LATCH, UNLATCH
DELAY TRAIL
OFF, ON
RETRIGGER FADE
OFF, ON
KNOB-L ASSIGN
KNOB-R ASSIGN
KNOB-C ASSIGN
ENCODER ASSIGN
EXP/FS ASSIGN
BPM SETTING
SYNC, OFF, 030
〜
600
LOOP RATE MODE
MANUAL, ENV, RANDOM
Pressing the
【
HOME
】
switch to show the desired setting screen
Pressing the
【◀】
/
【▶】
cursor Key to show the desired setting screen
Hold down the
【
HOME
】
switch for about 2 secons to show the Global Setting screen
USe the
【◀】
/
【▶】
cursor key to show the desired setting screen
Turn the
【
PARAMETER
】
encoder to show the desired setting menu
