Free Spirits HD XL Instructions Manual Download Page 20

Telefono 0039 (0) 445-390437  

Email [email protected]

Fax 0039 (0) 445-395539  

Site: www.freespirits.it

With the shipment of the order the buyer accepts the following conditions 

Warranty 

 

1. The SELLER warrants, for a period of twelve months after the date of delivery of the PRODUCTS to the BUYER, 

that the PRODUCTS are free from defects in manufacture and/or design which make the PRODUCTS unsuitable for 

the use for which the SELLER expressly represented to the BUYER the PRODUCTS are intended.

-

DUCTS without the consent of the SELLER, or has failed to communicate, via registered mail, the defects of the 

PRODUCTS or the lack of conformity thereof.

3.The SELLER shall be released from any responsibility if :

a) the replacement and/or the repair of the PRODUCTS is to be accounted to force majeure events, as described 

under article 7 below, or the BUYER’s, or its clients’, fault or negligence; or

b) the PRODUCTS, or parts thereof, have been misused or mishandled by the BUYER or its clients.

4.The SELLER shall be entitled to withdraw any defective PRODUCTS from the market, at its own expenses, and to 

obtain, to the extent it is possible, the BUYER’s assistance in this respect

5.Such with the exception of fraud, the SELLER shall be responsible exclusively for repairing and/or replacing any 

PRODUCTS which are defective and/or not complying with the order. For this purpose is made prior obligation to the 

BUYER, on penalty of forfeiture to the warranty:

a) To report in writing to the seller by registered letter with acknowledgment of receipt the presence of the reported 

6.In no event shall the SELLER’s liability of any kind include any damages to persons or property or any indirect, 

incidental or consequential losses which may have been caused to the BUYER or third parties by any defects or lack 

of conformity of the PRODUCTS

7.The  SELLER  sells  the  PRODUCTS  only  and  exclusively  to  authorized  workshops  performing  the  PRODUCTS 

therefore does not entitle the PURCHASER  to give for whatever reason the PRODUCTS to anyone without also 

providing installation. In case such an event occurs, the SELLER is relieved of any responsibility and the BUYER 

assumes any consequences related to lack of installation.

8.It is understood that the PURCHASER assumes all responsibility for problems that may arise due to the incorrect 

installation of the PRODUCTS.

Claims

-We check carefully and we pack accurately our goods before shipment. All claims due to damage or loss during the 

transport must be passed directly from the buyer to the courier that made delivery.

 

Consequently it is important that the buyer opposes terms on the relative bill of lading, so as he could receive possible 

reimbursements.

-Free Spirits srl company is not responsible for damages during transport. 

Final revisions

-Free Spirits srl company has got no connection with Harley-Davidson, Buell and Triumph brands. They are used only 

as references.

-The BUYER declares to be completely informed that some PRODUCTS in this catalogue could not comply with the 

-

 

-Free Spirits srl company declines any responsibility with the wrong use of its accessories.

  

To read “ Terms of Service” visit our website:  http://www.freespirits.it

Summary of Contents for HD XL





















Reviews: