background image

Contents

Autoset Programming for Quick setup ...........................................................................................................1

Programming the Remotes ............................................................................................................................1

Programming after the completed Autoset ....................................................................................................2

Continuous Force Learning Mode ..................................................................................................................2

Programming for Wired Wall Button ...............................................................................................................2

Troubleshooting ............................................................................................................................................2

Programming the Wired Wall Button from Start of Menu ................................................................................ 3

Homelink Programming .................................................................................................................................3

Wireless Wall Button Programming ................................................................................................................4

Outdoor Keypad Programming .......................................................................................................................4

Programming the Keypad  .............................................................................................................................5

Changing the Default Code for Channels ........................................................................................................5

Additional Codes ...........................................................................................................................................5

Changing a Current Passcode ........................................................................................................................5

Regular Use of Outdoor Keypad .....................................................................................................................6

Outdoor Keypad Reset ...................................................................................................................................6

Wi-Fi Hub ......................................................................................................................................................6

Error01 Troubleshooting ................................................................................................................................7

Manufacturer’s Step by Step Guide for Error01 ..............................................................................................7

Summary of Contents for Thalia














Reviews: