background image

3

Technical Specifications

Stock code _________________ EF1-230V
Supply voltage ______________ 230 V +/- 15% (194 V to 264 V)
Supply frequency ____________ 50/60 Hz (40 Hz to 70 Hz)
Supply power _______________ 2.8 kW / 3.5 kVA
Supply protection ____________ Class 1 earthed (grounded)
Environmental protection ______ IP65
Operating temperature ________ -15 ºC (5 ºF) to +45 ºC (113 ºF)

Shipping dimensions 

460 mm (18") wide x 210 mm (8.3") deep 

x 210 mm (8.3”) high

Shipping weight _____________ 3.6 kg (8 lb)

Power Supply

Welder must be powered with:

•   A quality 230 VAC, 50 Hz power supply with maximum tolerance of ± 15%.
•   A quality generator capable of supplying a minimum of 2.8 kW (3.5 kVA). 

Note that an earth-spike (grounding rod) must be used with generators.

If used with a 110v to 230v step-up transformer follow these specifications:  
•   Safety Isolating transformer: 3.3 kVA minimum.
•   Auto transformer: 3.3 kVa minimum.

Extension  Cords / Cables

Extension cables must comply with or be equivalent to  H07RN-F 

specifications. Cable use must comply with the following table.

Wire Size 

Metric

AWG Wire 

Size

Maximum 

Length, 

meters

Maximum 

Length, feet

1.5 mm

15

25

82

2.5 mm

13

50

164

4.0 mm

11

75

246

Note:

  All cable must be unwound from reel to prevent inductive heating 

effects.

Summary of Contents for EF1-230V













Reviews: