background image

 

SECTION I. INTRODUCTION 

 

Congratulations, you have just purchased one of 
the finest Point-of-Use Nitrate Reduction 
Appliances available.   

 

Like any other fine product, this appliance requires 
periodic maintenance in accordance with the 
schedule outlined.  Have your water checked 
periodically to verify nitrate reduction. 

 

Your new Nitrate Reduction (NRS-1) Drinking 
Water system uses a non-leaching material to 
reduce unwanted nitrates in a water supply. 

 

 

LIABLITY 

 

All information and recommendations appearing in this manual 
concerning the use of products described herein are based on 
information contained in good faith but makes no representation as to its 
comprehensiveness or accuracy. However, it is 

the user’s res

ponsibility to 

determine the suitability for his own use of such products. Since the actual 
use by others is beyond our control, no guarantee, expressed or implied, is 
made by Franklin Electric Co., Inc. (FECI) as to the effects of such use or 
the results to be obtained. FECI assumes no liability arising out of the use 
by others of such products. Nor is the information herein to be construed 
as absolutely complete, since additional information may be necessary or 
desirable when particular or exceptional conditions or circumstances exist 
or because of applicable laws or government regulations.

 

 

 
 
 

 
SECTION II. 

SPECIFICATIONS

  

 
 
 

TABLE A 

– RECOMMENDED OPERATING LIMITS FOR FEED WATER

 

 

Specifications 

 

 

 

 

NRC10 

Water Pressure 

 

 

 

 

40-100 psig  

Temperature   

 

 

 

 

40-100°F  

pH 

 

 

 

 

 

 

4.5-8.5 

Hardness 

 

 

 

 

 

Less than 1 gpg  

Iron 

 

 

 

 

 

 

Less than 0.05 ppm 

Manganese 

 

 

 

 

 

Less than 0.05 ppm  

Nitrate  

 

 

 

 

 

Less than 21 ppm (Does not apply to FSN Series Units) 

Bacteria 

 

 

 

 

 

Must be potable** 

NOTE: The NRS-1 may be installed on waters containing nitrate; however the total nitrate concentration of the incoming water 
supply should be less than 21.0 ppm.  Water containing nitrate concentration greater than 20.0 ppm will greatly reduce the 
cartridge capacity and leave potential for harmful levels of nitrate bleed through.  Have your water checked periodically to 
avoid harmful levels of nitrate bleed through.

 

 
**DO

 

NOT

 

USE

 

WITH

 

WATER

 

THAT

 

IS

 

MICROBIOLOGICALLY

 

UNSAFE

 

OR

 

OF

 

UNKNOWN

 

QUALITY. 

 
 

TABLE B 

– SYSTEM SPECIFICATIONS

 

 

Specifications 

 

 

 

 

NRS-1 

Overall Height  

 

 

 

 

14” 

I/O 

 

 

 

 

 

 

¼” 

Flow Rate 

 

 

 

 

 

1 gpm 

 
 
 
 
 
 
 

Recommended Filter Change Schedule* 

 

– NRC10 – Nitrate Filter: 

 

 

 

<=10 ppm nitrate………………………...200 gallons 
<=15 ppm ni

trate………………………...150 gallons 

<=20 ppm nitrate………………………...100 gallons 
>20 ppm nitrate, Install FSN Series nitrate reducer 

at point-of-entry 

 

Summary of Contents for NRS-1














Reviews: