background image

11

12

Your NOVA umbrella comes with a hinged spigot. Once you have installed the spigot according to 
the instructions below, slide the umbrella on to the top of the spigot and raise the umbrella. This 
is recommended as a 2-3 person operation.

• 

Deck Plate and deck bolts (purchased by you or supplied by your hired professional 
contractor)

• 

A decently amp rated corded or cordless power drill. 

• 

A scrap piece of wood (to make a reinforcing brace/blocking) and suitable hardware to 
secure the blocking to the deck joists.

Once you have decided on the location of the NOVA/Deck Plate, use the four outer holes in the 
deck plate as a template to start drilling each of the holes in the deck. Make sure each of the 
four holes go through decking and miss the joists. Using the four holes drilled in the deck as a 
guide, you now need to install a reinforcing brace/blocking hard up under the decking for the 
deck plate bolts to be fixed into. It is recommended that two wood brace/blocking be secured 
between the deck joists or bearers that form the structural frame of the deck. Ideally the brace/
blocking should be two short lengths of 4”x4” wood posts side by side, or alternatively two 
pieces of 2”x8” wood joists joined together for the umbrella deck plate to bolt through. The 
brace/blocking must then be securely fixed to the deck frame/joists using suitable hardware. 
These may be large galvanized nails, coach screws or builders brackets etc. If the installation is 
in a sea spray zone or coastal environment, then stainless steel hardware is recommended. 

You can now use the four holes already drilled in your decking and drill them all the way through 
the newly installed brace/blocking under the decking. Put the deck plate in place and install 
purchased through the plate, decking and blocking. Use a washer and nut on the underside of 
the bolt under the deck and torque down tight. After the deck plate has been securely fixed to 
the deck. 

You should now remove the four “grub bolts” that are installed in the four spigot-bolt holes. (

The 

purpose of these grub bolts is to keep dirt out of the threaded holes when not in use

). Attach 

the spigot to the deck plate using the supplied hardware and tighten down with the supplied 
Allen key. Slide your NOVA umbrella onto the spigot, walk the umbrella upright and lock the spigot 
down to the mounting plate. Now you can carefully open your umbrella for the first time.

WOOD DECK INSTALLATION

TOOLS NEEDED

• 

IMPORTANT

: Your umbrella must be bolted down into a reinforced brace/blocking that is 

fixed under the deck planks to the deck joist. The umbrella must not only be fixed to the 
deck planking as this will likely result in the deck planks “pulling up” and the umbrella falling 
over in high winds.

SUPPLIED STAINLESS STEEL (4x 1/2”)
COUNTERSUNK BOLTS

RECOMMENDED 
(1/2”x6”STAINLESS STEEL WOOD FASTENERS)

SPIGOT

12.5” DECK PLATE

DECK PANELS (BOARDS)

DECK JOISTS

BRACE/BLOCKING

WOOD DECK

INSTALLATION HARDWARE NOT INCLUDED. 

HARDWARE INCLUDED WITH UMBRELLA

Galvanized Steel Spigot (29)
Spigot Mounting Hardware: 4x 1/2” (1.38mm) Stainless Steel Countersunk Bolts
1x 5/16” (8mm) Allen Wrench

INSTALLATION HARDWARE NOT INCLUDED. 

Summary of Contents for NOVA NGU













Reviews: