TECHNICAL DATA
NOTE:
Call us immediatly if you see inconsistencies.
(1- 800-626-5771)
or visit
www.frankeksd.com
CONTENTS IN BOX
1
Faucet assembly
2 Rubber washer
3
Rubber washer
4
Plastic flange
5 Fixing plate
6
Fixing nut
12 Sealing washer
13 Side spray mounting flange
INSTALLATION INSTRUCTIONS
1. Remove all contents from the package and check for completeness.
2. Flush pipe work to ensure it is free from debris.
3. Turn off water supply.
4. Remove faucet and hardware from its protective packaging.
Faucet comes assembled.
5. Cut a mounting hole 1 3/8 diameter (35mm) in the desired position in
counter top or sink (if one isn’t available).
6. Place the rubber washer (2) over the hole for the faucet body
1
5
6
11
Flow Rate
Recommended Water Pressure
Max. Water Pressure
Recommended Hot Water Temp.
Hole Size For side spray
Certifies this faucet complies with ASME A112.18.1 / CSA B125.1
& NSF 61, NSF 372 and AB1953
1.75 GPM at 45 PSI
30-75 PSI
145 PSI
120°-140° F
1 3/8”
2
4
3
10
7
9
7 Supply hoses
8
Side spray supply hose
9
Side spray return hose
Side spray shower
11
2
5
1
7
4
3
6
8
10
20
21
17
15
18
14
11
9
14
16
8
13
19
17
15 Rubber washer
16 Plastic spacer
Rubber washer
14
18
20
21
Side spray diverter
10
17 Fixing plate
18 Fixing nut
13
19
19 SIde spray supply hose
20 Weight
22
ATTENTION
: For steps 6 and 9
The washer should be sitting between the countertop and faucet base.
DO NOT
use putty or other sealant at this location. For solid surface
installation the countertop mounting surface needs to be flat and free of
debris, otherwise the faucet or side spray may not sit properly. For tile
installations, avoid installing faucet or side spray near or on top of grout
lines. This may cause a weak joint and could cause leaks.
7. Install the mounting hardware to the base of the faucet body in the
following order – rubber washer (3), plastic flange (4), fixing plate (5), and
fixing nut (6) as illustrated.
8. Tighten the fixing nut (6) onto the body (1)
9. Place the rubber washer (14) over hole for the side spray mounting
flange (13)
10. Install the side spray mounting hardware to the base of the side
spray mounting flange (13), in the following order – rubber washer (15),
Plastic spacer (16), fixing plate (17), and fixing nut (18).
11. Connect side spray shower (11) to side spray supply hose (19) by
hand. Make sure sealing washer (12) is in place on the supply hose,
otherwise the side spray will leak.
12. Insert the side spray supply hose (19) into the side spray mounting
flange (13) from the top
13. Connect the side spray supply hose (8) coming from the faucet
body to the top of the side spray diverter (10).
14. Connect the side spray return hose (9) to the left side (largest
fitting) of the side spray diverter (10).
16. Secure the weight (20) to the side spray supply hose (19) with the
screws (21) approximately 2” (50mm) above the bend in the bottom of
the side spray supply hose (19).
17. Connect the supply hoses (7) to the water supply in the home and
turn on the faucet. Ensure everything is functioning properly and
check/test for leaks.
15. Connect the bottom (smallest fitting) of the side spray diverter (10) to
the side spray supply hose (19).
21 Screws
22 Aerator wrench
12
15
16
12
2” (50 mm)